você pode ler este artigo e tente:
sudo modprobe rtl8192cu swenc=1
echo "2001 330D" | sudo tee /sys/bus/usb/drivers/rtl8192cu/new_id
Dongle sem fio DWA-131 não está funcionando
1
Eu comprei um dongle USB sem fio dlink dwa-131. Mas eu sou incapaz de falar sobre isso. Eu li na lista de hardware suportado que este é plug and play no Ubuntu.
Eu vi o procedimento de solução de problemas sem fio e obtive os registros. Eu colei abaixo do log. Também vejo dlink listado em lsusb. Mas não é visto no log abaixo. O chip Intel Pro não está funcionando. Daí eu trouxe este dongle.
Eu não consegui colar o log porque houve um erro em que precisei de 10 reputação para postar mais de dois links. Por isso, eu deletei os links no log.
W: Some index files failed to download. They have been ignored, or old ones used instead.
Reading package lists... Done
Building dependency tree
Reading state information... Done
E: Unable to locate package hwinfo
*-network DISABLED
description: Wireless interface
product: PRO/Wireless 3945ABG [Golan] Network Connection
vendor: Intel Corporation
physical id: 0
bus info: pci@0000:10:00.0
logical name: wlan0
version: 02
serial: 00:1f:3c:a0:c6:69
width: 32 bits
clock: 33MHz
capabilities: pm msi pciexpress bus_master cap_list ethernet physical wireless
configuration: broadcast=yes driver=iwl3945 driverversion=3.13.0-32-generic firmware=N/A latency=0 link=no multicast=yes wireless=IEEE 802.11abg
resources: irq:42 memory:f0000000-f0000fff
*-network
description: Ethernet interface
product: 82562ET/EZ/GT/GZ - PRO/100 VE (LOM) Ethernet Controller Mobile
vendor: Intel Corporation
physical id: 8
bus info: pci@0000:02:08.0
logical name: eth0
version: 01
serial: 00:1e:ec:a1:d5:f0
size: 10Mbit/s
capacity: 100Mbit/s
width: 32 bits
clock: 33MHz
capabilities: pm bus_master cap_list ethernet physical tp mii 10bt 10bt-fd 100bt 100bt-fd autonegotiation
configuration: autonegotiation=on broadcast=yes driver=e100 driverversion=3.5.24-k2-NAPI duplex=half latency=64 link=no maxlatency=56 mingnt=8 multicast=yes port=MII speed=10Mbit/s
resources: irq:20 memory:f0101000-f0101fff ioport:2000(size=64)
0: phy0: Wireless LAN
Soft blocked: no
Hard blocked: yes
wlan0 Interface doesn't support scanning : Network is down
lo Interface doesn't support scanning.
eth0 Interface doesn't support scanning.
arquivo interfaces (5) usado por ifup (8) e ifdown (8)
auto lo
iface lo inet loopback
DISTRIB_ID=Ubuntu
DISTRIB_RELEASE=14.04
DISTRIB_CODENAME=trusty
DISTRIB_DESCRIPTION="Ubuntu 14.04.1 LTS"
02:08.0 Ethernet controller [0200]: Intel Corporation 82562ET/EZ/GT/GZ - PRO/100 VE (LOM) Ethernet Controller Mobile [8086:1068] (rev 01)
Subsystem: Hewlett-Packard Company Device [103c:30d5]
Kernel driver in use: e100
10:00.0 Network controller [0280]: Intel Corporation PRO/Wireless 3945ABG [Golan] Network Connection [8086:4222] (rev 02)
Subsystem: Hewlett-Packard Company Device [103c:135b]
Kernel driver in use: iwl3945
Bus 001 Device 002: ID 2001:330d D-Link Corp.
Bus 001 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub
Bus 002 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
RUNNING STATE WIFI-HARDWARE WIFI WWAN-HARDWARE WWAN
running disconnected disabled disabled enabled disabled
Caminho de H / W Descrição da Classe de Dispositivo
system HP 520 Notebook PC (FH562AA#UUF)
/0 bus 30D5
/0/0 memory 128KiB BIOS
/0/4 processor Intel(R) Core(TM) Duo CPU T2700 @ 2.33GHz
/0/4/5 memory 64KiB L1 cache
/0/4/6 memory 2MiB L2 cache
/0/4/0.1 processor Logical CPU
/0/4/0.2 processor Logical CPU
/0/a memory 3GiB System Memory
/0/a/0 memory 1GiB SODIMM DDR2 Synchronous 667 MHz (1.5 ns)
/0/a/1 memory 2GiB SODIMM DDR2 Synchronous 667 MHz (1.5 ns)
/0/100 bridge Mobile 945GSE Express Memory Controller Hub
/0/100/2 display Mobile 945GSE Express Integrated Graphics Controller
/0/100/2.1 display Mobile 945GM/GMS/GME, 943/940GML Express Integrated Graphics Controller
/0/100/1b multimedia NM10/ICH7 Family High Definition Audio Controller
/0/100/1c bridge NM10/ICH7 Family PCI Express Port 1
/0/100/1c.1 bridge NM10/ICH7 Family PCI Express Port 2
/0/100/1c.1/0 wlan0 network PRO/Wireless 3945ABG [Golan] Network Connection
/0/100/1d bus NM10/ICH7 Family USB UHCI Controller #1
/0/100/1d.7 bus NM10/ICH7 Family USB2 EHCI Controller
/0/100/1e bridge 82801 Mobile PCI Bridge
/0/100/1e/6 bridge CB1410 Cardbus Controller
/0/100/1e/8 eth0 network 82562ET/EZ/GT/GZ - PRO/100 VE (LOM) Ethernet Controller Mobile
/0/100/1f bridge 82801GBM (ICH7-M) LPC Interface Bridge
/0/100/1f.2 storage 82801GBM/GHM (ICH7-M Family) SATA Controller [IDE mode]
/0/1 scsi0 storage
/0/1/0.0.0 /dev/sda disk 500GB TOSHIBA MQ01ABD0
/0/1/0.0.0/1 /dev/sda1 volume 55GiB Windows NTFS volume
/0/1/0.0.0/2 /dev/sda2 volume 410GiB Extended partition
/0/1/0.0.0/2/5 /dev/sda5 volume 195GiB HPFS/NTFS partition
/0/1/0.0.0/2/6 /dev/sda6 volume 172GiB HPFS/NTFS partition
/0/1/0.0.0/2/7 /dev/sda7 volume 3060MiB Linux swap / Solaris partition
/0/1/0.0.0/2/8 /dev/sda8 volume 39GiB Linux filesystem partition
/0/2 scsi1 storage
/0/2/0.0.0 /dev/cdrom disk DVDRAM GSA-T20N
Linux prasanna 3.13.0-32-generic #57-Ubuntu SMP Tue Jul 15 03:51:12 UTC 2014 i686 i686 i686 GNU/Linux
[ 0.000000] DMI: Hewlett-Packard HP 520 Notebook PC/30D5, BIOS 68MVU Ver. F.07 03/18/2008
[ 0.000000] Found optimal setting for mtrr clean up
[ 0.124777] ACPI: No dock devices found.
[ 0.125240] [Firmware Bug]: ACPI: No _BQC method, cannot determine initial brightness
[ 0.125278] [Firmware Bug]: ACPI: No _BQC method, cannot determine initial brightness
[ 0.160686] acpi PNP0A08:00: [Firmware Info]: MMCONFIG for domain 0000 [bus 00-3f] only partially covers this bridge
[ 0.166459] Found 1 acpi root devices
[ 0.166601] usbcore: registered new interface driver usbfs
[ 0.166601] usbcore: registered new interface driver hub
[ 0.166601] usbcore: registered new device driver usb
[ 0.170087] Switched to clocksource hpet
[ 0.179321] pnp: PnP ACPI: found 11 devices
[ 0.218302] pci 0000:02:08.0: Firmware left e100 interrupts enabled; disabling
[ 0.668099] Console: switching to colour frame buffer device 128x48
[ 0.696460] input: Lid Switch as /devices/LNXSYSTM:00/device:00/PNP0C0D:00/input/input1
[ 0.696494] ACPI: Lid Switch [C20C]
[ 0.808119] usb usb1: New USB device found, idVendor=1d6b, idProduct=0002
[ 0.808122] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 0.808125] usb usb1: Product: EHCI Host Controller
[ 0.808128] usb usb1: Manufacturer: Linux 3.13.0-32-generic ehci_hcd
[ 0.808130] usb usb1: SerialNumber: 0000:00:1d.7
[ 0.808257] hub 1-0:1.0: USB hub found
[ 0.808932] usb usb2: New USB device found, idVendor=1d6b, idProduct=0001
[ 0.808935] usb usb2: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 0.808938] usb usb2: Product: UHCI Host Controller
[ 0.808940] usb usb2: Manufacturer: Linux 3.13.0-32-generic uhci_hcd
[ 0.808943] usb usb2: SerialNumber: 0000:00:1d.0
[ 0.809057] hub 2-0:1.0: USB hub found
[ 0.817703] Loaded X.509 cert 'Magrathea: Glacier signing key: a7fc6590fc4a8d859aaebda2ca5dd04716244fa0'
[ 0.885012] IMA: No TPM chip found, activating TPM-bypass!
[ 0.886064] BIOS EDD facility v0.16 2004-Jun-25, 0 devices found
[ 1.097279] isapnp: No Plug & Play device found
[ 1.120094] usb 1-2: new high-speed USB device number 2 using ehci-pci
[ 1.261678] usb 1-2: New USB device found, idVendor=2001, idProduct=330d
[ 1.261683] usb 1-2: New USB device strings: Mfr=1, Product=2, SerialNumber=3
[ 1.261686] usb 1-2: Product: 802.11n WLAN Adapter
[ 1.261689] usb 1-2: Manufacturer: Realtek
[ 1.261691] usb 1-2: SerialNumber: 00e04c000001
[ 1.264957] e100 0000:02:08.0 eth0: addr 0xf0101000, irq 20, MAC addr 00:1e:ec:a1:d5:f0
[ 9.280791] IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready
[ 9.595991] [Firmware Bug]: _BCQ is used instead of _BQC
[ 9.596042] [Firmware Bug]: ACPI: No _BQC method, cannot determine initial brightness
[ 9.606285] lp: driver loaded but no devices found
[ 9.669604] Console: switching to colour dummy device 80x25
[ 9.676143] cfg80211: Calling CRDA to update world regulatory domain
[ 9.781350] iwl3945: Intel(R) PRO/Wireless 3945ABG/BG Network Connection driver for Linux, in-tree:s
[ 9.781356] iwl3945: Copyright(c) 2003-2011 Intel Corporation
[ 9.787063] iwl3945 0000:10:00.0: can't disable ASPM; OS doesn't have ASPM control
[ 9.853481] iwl3945 0000:10:00.0: Tunable channels: 11 802.11bg, 13 802.11a channels
[ 9.853487] iwl3945 0000:10:00.0: Detected Intel Wireless WiFi Link 3945ABG
[ 9.853563] iwl3945 0000:10:00.0: irq 42 for MSI/MSI-X
[ 9.863209] yenta_cardbus 0000:02:06.0: CardBus bridge found [103c:30d5]
[ 9.877750] ieee80211 phy0: Selected rate control algorithm 'iwl-3945-rs'
[ 9.971759] usbcore: registered new interface driver rtl8192cu
[ 10.436116] Console: switching to colour frame buffer device 160x50
[ 10.440962] lpc_ich: Resource conflict(s) found affecting gpio_ich
[ 10.448407] leds_ss4200: no LED devices found
[ 10.844713] cfg80211: World regulatory domain updated:
[ 10.844720] cfg80211: (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp)
[ 10.844722] cfg80211: (2402000 KHz - 2472000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
[ 10.844725] cfg80211: (2457000 KHz - 2482000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
[ 10.844727] cfg80211: (2474000 KHz - 2494000 KHz @ 20000 KHz), (300 mBi, 2000 mBm)
[ 10.844729] cfg80211: (5170000 KHz - 5250000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
[ 10.844731] cfg80211: (5735000 KHz - 5835000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
[ 10.901287] EXT4-fs (sda8): re-mounted. Opts: errors=remount-ro
[ 14.606592] IPv6: ADDRCONF(NETDEV_UP): wlan0: link is not ready
[ 14.626272] IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready
[ 14.627509] IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready
[ 15.248165] type=1400 audit(1418673050.858:48): apparmor="STATUS" operation="profile_replace" profile="unconfined" name="/usr/lib/telepathy/telepathy-ofono" pid=745 comm="apparmor_parser"
[ 15.248956] type=1400 audit(1418673050.858:50): apparmor="STATUS" operation="profile_replace" profile="unconfined" name="/usr/lib/telepathy/telepathy-ofono" pid=745 comm="apparmor_parser"
[ 15.249291] type=1400 audit(1418673050.858:51): apparmor="STATUS" operation="profile_replace" profile="unconfined" name="/usr/lib/telepathy/telepathy-ofono" pid=745 comm="apparmor_parser"
Release Date: 03/18/2008
Serial services are supported (int 14h)
Manufacturer: Hewlett-Packard
Product Name: HP 520 Notebook PC
Serial Number: CND8374QLD
Manufacturer: Hewlett-Packard
Product Name: 30D5
Serial Number: Not Specified
Manufacturer: Hewlett-Packard
Serial Number: CND8374QLD
Manufacturer: Intel(R)
Serial Number: Not Specified
Manufacturer: CE00000000000000
Serial Number: 303EDB82
Manufacturer: 7F98000000000000
Serial Number: 7A15580F
wlan0 IEEE 802.11abg ESSID:off/any
Mode:Managed Access Point: Not-Associated Tx-Power=off
Retry long limit:7 RTS thr:off Fragment thr:off
Power Management:off
lo no wireless extensions.
eth0 no wireless extensions.
install snd-rawmidi /sbin/modprobe --ignore-install snd-rawmidi $CMDLINE_OPTS && { /sbin/modprobe --quiet --use-blacklist snd-seq-midi ; : ; }
# which ath5k cannot recover. To prevent this condition, stop
blacklist ath_pci
blacklist eth1394
# replaced by p54pci
blacklist prism54
# replaced by b43 and ssb.
blacklist bcm43xx
blacklist acer-wmi
blacklist uart6850
blacklist twl4030_wdt
# /etc/modprobe.d/iwlwifi.conf
# iwlwifi will dyamically load either iwldvm or iwlmvm depending on the
# microcode file installed on the system. When removing iwlwifi, first
# remove the iwl?vm module and then iwlwifi.
remove iwlwifi \
(/sbin/lsmod | grep -o -e ^iwlmvm -e ^iwldvm -e ^iwlwifi | xargs /sbin/rmmod) \
&& /sbin/modprobe -r mac80211
[main]
NetworkingEnabled=true
WirelessEnabled=true
WWANEnabled=true
WimaxEnabled=true
sudo: hwinfo: command not found
root 669 0.0 0.3 54488 10208 ? Ssl 01:20 0:00 NetworkManager
prasanna 2277 0.0 0.0 4432 768 pts/2 S+ 01:26 0:00 egrep --color=auto wpa|icd|etwork
Kernel IP routing table
Destination Gateway Genmask Flags MSS Window irtt Iface
# Dynamic resolv.conf(5) file for glibc resolver(3) generated by resolvconf(8)
# DO NOT EDIT THIS FILE BY HAND -- YOUR CHANGES WILL BE OVERWRITTEN
total 28428
2097153 drwxr-xr-x 3 root root 4096 Dec 8 06:23 .
2 drwxr-xr-x 22 root root 4096 Dec 8 06:21 ..
2097156 -rw-r--r-- 1 root root 1166929 Jul 15 10:36 abi-3.13.0-32-generic
2097157 -rw-r--r-- 1 root root 169732 Jul 15 10:36 config-3.13.0-32-generic
2097154 drwxr-xr-x 5 root root 4096 Dec 8 06:22 grub
2097173 -rw-r--r-- 1 root root 18701723 Dec 8 06:23 initrd.img-3.13.0-32-generic
2097158 -rw-r--r-- 1 root root 176500 Mar 12 2014 memtest86+.bin
2097159 -rw-r--r-- 1 root root 178176 Mar 12 2014 memtest86+.elf
2097160 -rw-r--r-- 1 root root 178680 Mar 12 2014 memtest86+_multiboot.bin
2097155 -rw------- 1 root root 2693057 Jul 15 10:36 System.map-3.13.0-32-generic
2109674 -rw-r--r-- 1 root root 5820336 Jul 23 03:54 vmlinuz-3.13.0-32-generic
Support status summary of 'prasanna':
You have 1693 packages (100.0%) that can not/no-longer be downloaded
You have 0 packages (0.0%) that are unsupported
Run with --show-unsupported, --show-supported or --show-all to see more details
--2014-12-16 01:26:28-- http://www.linux-usb.org/usb.ids
Resolving www.linux-usb.org (www.linux-usb.org)... failed: Name or service not known.
wget: unable to resolve host address ‘www.linux-usb.org’
update-usbids: download failed
Module Size Used by
bnep 18895 2
rfcomm 53664 0
bluetooth 342206 10 bnep,rfcomm
snd_hda_codec_conexant 47785 1
hp_wmi 13702 0
sparse_keymap 13708 1 hp_wmi
pcmcia 51828 0
parport_pc 31981 0
coretemp 13195 0
ppdev 17391 0
rtl8192cu 66675 0
kvm 388083 0
snd_hda_intel 42730 2
snd_hda_codec 164067 2 snd_hda_codec_conexant,snd_hda_intel
snd_hwdep 13272 1 snd_hda_codec
snd_pcm 85501 2 snd_hda_codec,snd_hda_intel
joydev 17101 0
arc4 12536 2
yenta_socket 40201 0
pcmcia_rsrc 18319 1 yenta_socket
rtl_usb 18072 1 rtl8192cu
serio_raw 13230 0
lpc_ich 16864 0
pcmcia_core 22328 3 pcmcia,pcmcia_rsrc,yenta_socket
iwl3945 63619 0
iwlegacy 88016 1 iwl3945
rtlwifi 52835 2 rtl_usb,rtl8192cu
snd_page_alloc 14230 2 snd_pcm,snd_hda_intel
rtl8192c_common 47340 1 rtl8192cu
snd_seq_midi 13132 0
mac80211 546051 5 iwl3945,iwlegacy,rtl_usb,rtlwifi,rtl8192cu
snd_seq_midi_event 14475 1 snd_seq_midi
snd_rawmidi 25135 1 snd_seq_midi
snd_seq 55383 2 snd_seq_midi_event,snd_seq_midi
snd_seq_device 14137 3 snd_seq,snd_rawmidi,snd_seq_midi
snd_timer 28584 2 snd_pcm,snd_seq
cfg80211 409394 4 iwl3945,iwlegacy,mac80211,rtlwifi
i915 705659 3
wmi 18673 1 hp_wmi
drm_kms_helper 47182 1 i915
snd 60871 14 snd_hwdep,snd_timer,snd_hda_codec_conexant,snd_pcm,snd_seq,snd_rawmidi,snd_hda_codec,snd_hda_intel,snd_seq_device,snd_seq_midi
video 18903 1 i915
lp 13299 0
parport 40836 3 lp,ppdev,parport_pc
mac_hid 13037 0
drm 244037 4 i915,drm_kms_helper
i2c_algo_bit 13197 1 i915
soundcore 12600 1 snd
psmouse 91329 0
e100 35945 0
mii 13654 1 e100
obrigado a todos
por pachu
15.12.2014 / 16:19
3 respostas
1
por
Uli Middelberg
20.01.2015 / 09:33
1
Meu dongle Wi-Fi D-link tem as seguintes especificações:
- Adaptador USB Sem Fio N300 D-Link
- Número do modelo: DWA-131
- Versão de H / W: E1
- Versão F / W: 5.00
Aqui está o que eu fiz, depois de procurar na internet por um longo tempo:
1) Vá para link e baixe o arquivo "DWA-131 Driver Linux v4.3.1.1.zip (5.88 MB) "na seção" REV E "(no topo da página). 2) Mova o arquivo para um diretório de sua escolha, extraia-o e mude para o diretório que acabou de extrair. Isso é (no diretório que você escolheu):
- tar -zxvf 20140812_rtl8192EU_linux_v4.3.1.1_11320.tar.gz
- cd 20140812_rtl8192EU_linux_v4.3.1.1_11320 /
3) Digite os seguintes comandos:
- fazer
- su (sua senha será necessária)
- faça a instalação
Você nem precisa reiniciar o computador. No meu caso, funcionou instantaneamente.
Espero que você ache esta informação útil.
por
Ignacio Hernandez Montilla
01.04.2016 / 12:21
0
link
Você já tentou apertar o botão à esquerda do botão liga / desliga para ver se ele habilita o wifi, ele é o número 2 da imagem. Se funcionar como projetado, deve pelo menos alternar o bloco rígido em rfkill list all
por
Jeremy31
01.04.2016 / 15:42