classificamos com este link :: link
tem que excluir o ataque.
Mostre o raid dar index com este comando :: sas2ircu LIST
root@lancache:~# sas2ircu LIST
LSI Corporation SAS2 IR Configuration Utility.
Version 13.00.00.00 (2012.02.17)
Copyright (c) 2009-2012 LSI Corporation. All rights reserved.
Adapter Vendor Device SubSys SubSys
Index Type ID ID Pci Address Ven ID Dev ID
----- ------------ ------ ------ ----------------- ------ ------
0 SAS2008 1000h 72h 00h:01h:00h:00h 1028h 1f1dh
SAS2IRCU: Utility Completed Successfully.
O índice é 0
Agora preciso do ID do volume de raid
root@lancache:~# sas2ircu 0 DISPLAY
LSI Corporation SAS2 IR Configuration Utility.
Version 13.00.00.00 (2012.02.17)
Copyright (c) 2009-2012 LSI Corporation. All rights reserved.
Read configuration has been initiated for controller 0
------------------------------------------------------------------------
Controller information
------------------------------------------------------------------------
Controller type : SAS2008
BIOS version : 7.11.01.00
Firmware version : 7.15.04.00
Channel description : 1 Serial Attached SCSI
Initiator ID : 0
Maximum physical devices : 39
Concurrent commands supported : 2607
Slot : 1
Segment : 0
Bus : 1
Device : 0
Function : 0
RAID Support : Yes
------------------------------------------------------------------------
IR Volume information
------------------------------------------------------------------------
IR volume 1
Volume ID : 79
Status of volume : Inactive, Okay (OKY)
Volume wwid : 0edea3a351dff36d
RAID level : RAID0
Size (in MB) : 7629392
Physical hard disks :
PHY[0] Enclosure#/Slot# : 1:1
PHY[1] Enclosure#/Slot# : 1:0
PHY[2] Enclosure#/Slot# : 0:0
PHY[3] Enclosure#/Slot# : 0:0
------------------------------------------------------------------------
Physical device information
------------------------------------------------------------------------
Initiator at ID #0
Device is a Hard disk
Enclosure # : 0
Slot # : 0
SAS Address : 0000000-0-0000-0000
State : Missing (MIS)
Manufacturer : SEAGATE
Model Number :
Firmware Revision :
Serial No : Z1P14BEL0000C225
GUID : N/A
Drive Type : Undetermined
Device is a Hard disk
Enclosure # : 0
Slot # : 0
SAS Address : 0000000-0-0000-0000
State : Missing (MIS)
Manufacturer : SEAGATE
Model Number :
Firmware Revision :
Serial No : Z1P00HSD0000S129
GUID : N/A
Drive Type : Undetermined
Device is a Hard disk
Enclosure # : 1
Slot # : 0
SAS Address : 5000c50-0-342c-217d
State : Optimal (OPT)
Size (in MB)/(in sectors) : 1907729/3907029167
Manufacturer : SEAGATE
Model Number : ST2000NM0001
Firmware Revision : 0001
Serial No : Z1P0288F0000S137KRQ9
GUID : 5000c500342c217f
Protocol : SAS
Drive Type : SAS_HDD
Device is a Hard disk
Enclosure # : 1
Slot # : 1
SAS Address : 5000c50-0-8d46-33cd
State : Optimal (OPT)
Size (in MB)/(in sectors) : 1907729/3907029167
Manufacturer : SEAGATE
Model Number : ST2000NM0001
Firmware Revision : 0002
Serial No : Z1P2JXMV0000C2426MCF
GUID : 5000c5008d4633cf
Protocol : SAS
Drive Type : SAS_HDD
------------------------------------------------------------------------
Enclosure information
------------------------------------------------------------------------
Enclosure# : 1
Logical ID : 5782bcb0:2a464900
Numslots : 8
StartSlot : 0
------------------------------------------------------------------------
SAS2IRCU: Command DISPLAY Completed Successfully.
SAS2IRCU: Utility Completed Successfully.
So the Volum ID os 79 ...
Now to delete the volume.
root@lancache:~# sas2ircu 0 DELETEVOLUME 79
LSI Corporation SAS2 IR Configuration Utility.
Version 13.00.00.00 (2012.02.17)
Copyright (c) 2009-2012 LSI Corporation. All rights reserved.
You are about to delete an existing RAID Volume on a controller. This command
will delete the specified RAID volume and associated HotSpare drive(s).
WARNING: Proceeding with this operation may cause data loss or data
corruption. Are you sure you want to proceed (YES/NO)? yes
WARNING: This is you last chance to abort this operation. Do you wish
to abort (YES/NO)? no
Please wait, may take up to a minute...
SAS2IRCU: Volume deleted successfully.
SAS2IRCU: Command DELETEVOLUME Completed Successfully.
SAS2IRCU: Utility Completed Successfully.
Agora os discos estão de volta ao normal
root@lancache:~# lshw -c disk
*-disk:0
description: SCSI Disk
product: ST2000NM0001
vendor: SEAGATE
physical id: 0.0.0
bus info: scsi@0:0.0.0
logical name: /dev/sdc
version: 0001
serial: Z1P0288F0000S137KRQ9
size: 1863GiB (2TB)
capabilities: 7200rpm
configuration: ansiversion=6 logicalsectorsize=512 sectorsize=512
*-disk:1
description: SCSI Disk
product: ST2000NM0001
vendor: SEAGATE
physical id: 0.1.0
bus info: scsi@0:0.1.0
logical name: /dev/sdb
version: 0002
serial: Z1P2JXMV0000C2426MCF
size: 1863GiB (2TB)
capabilities: 7200rpm
configuration: ansiversion=6 logicalsectorsize=512 sectorsize=512
Agora eu posso fdisk as unidades e configurá-las com zfs.
Disk /dev/sdb: 1.8 TiB, 2000398934016 bytes, 3907029168 sectors
Units: sectors of 1 * 512 = 512 bytes
Sector size (logical/physical): 512 bytes / 512 bytes
I/O size (minimum/optimal): 512 bytes / 512 bytes
Disk /dev/sdc: 1.8 TiB, 2000398934016 bytes, 3907029168 sectors
Units: sectors of 1 * 512 = 512 bytes
Sector size (logical/physical): 512 bytes / 512 bytes
I/O size (minimum/optimal): 512 bytes / 512 bytes
Eu sei que é um post antigo, mas vale uma atualização para todos.