Eu tenho um laptop Acer rodando o Ubuntu 16.04. O laptop tem chip 802.11ad Wilocity wil6210. O driver - wil6210 usa firmware wil6210.fw e wil6210.brd .
No entanto, não consegui encontrar o firmware na Web.
A saída do lspci é:
Network controller: Wilocity Ltd. Wil6200 802.11ad Wireless Network Adapter (rev 02)
A saída do dmesg é:
[ 1.182576] nouveau: detected PR support, will not use DSM
[ 3.291185] wil6210 0000:03:00.0: wil6210 device found [1ae9:0310] (rev 2)
[ 3.311999] wil6210 0000:03:00.0 (unnamed net_device) (uninitialized): wil_pcie_probe: CSR at [mem 0x84000000-0x841fffff 64bit] -> 0xffffb05983400000
[ 3.328593] wil6210 0000:03:00.0 (unnamed net_device) (uninitialized): wil_set_capabilities: Board hardware is Sparrow B0
[ 3.329535] wil6210 0000:03:00.0 (unnamed net_device) (uninitialized): _wil6210_disconnect: _wil6210_disconnect(bssid= (null), reason=3, ev-)
[ 3.394610] wil6210 0000:03:00.0 (unnamed net_device) (uninitialized): wil_get_bl_info: Boot Loader struct v2: MAC = 04:ce:14:07:85:b0 RF = 0x0000 (status 0x0000) bband = 0x00000000
[ 3.394613] wil6210 0000:03:00.0 (unnamed net_device) (uninitialized): wil_get_bl_info: Boot Loader build 255.255.0.6836
[ 3.394614] wil6210 0000:03:00.0 (unnamed net_device) (uninitialized): wil_set_oob_mode: wil_set_oob_mode: enable=0
[ 3.492192] wil6210 0000:03:00.0 wlp3s0: renamed from wlan0
[ 4.758824] cgroup: new mount options do not match the existing superblock, will be ignored
[ 5.072628] wil6210 0000:03:00.0 wlp3s0: _wil6210_disconnect: _wil6210_disconnect(bssid= (null), reason=3, ev-)
[ 5.138722] wil6210 0000:03:00.0 wlp3s0: wil_get_bl_info: Boot Loader struct v2: MAC = 04:ce:14:07:85:b0 RF = 0x0000 (status 0x0000) bband = 0x00000000
[ 5.138723] wil6210 0000:03:00.0 wlp3s0: wil_get_bl_info: Boot Loader build 255.255.0.6836
[ 5.138725] wil6210 0000:03:00.0 wlp3s0: wil_set_oob_mode: wil_set_oob_mode: enable=0
[ 5.138727] wil6210 0000:03:00.0 wlp3s0: wil_reset: Use firmware <wil6210.fw> + board <wil6210.brd>
[ 5.138893] wil6210 0000:03:00.0: Direct firmware load for wil6210.fw failed with error -2
[ 5.138895] wil6210 0000:03:00.0 wlp3s0: wil_request_firmware: ERR[ FW ]Failed to load firmware wil6210.fw
[ 720.012611] wil6210 0000:03:00.0 wlp3s0: _wil6210_disconnect: _wil6210_disconnect(bssid= (null), reason=3, ev-)
[ 720.075072] wil6210 0000:03:00.0 wlp3s0: wil_get_bl_info: Boot Loader struct v2: MAC = 04:ce:14:07:85:b0 RF = 0x0000 (status 0x0000) bband = 0x00000000
[ 720.075074] wil6210 0000:03:00.0 wlp3s0: wil_get_bl_info: Boot Loader build 255.255.0.6836
[ 720.075076] wil6210 0000:03:00.0 wlp3s0: wil_set_oob_mode: wil_set_oob_mode: enable=0
[ 720.075079] wil6210 0000:03:00.0 wlp3s0: wil_reset: Use firmware <wil6210.fw> + board <wil6210.brd>
[ 720.075090] wil6210 0000:03:00.0: Direct firmware load for wil6210.fw failed with error -2
[ 720.075092] wil6210 0000:03:00.0 wlp3s0: wil_request_firmware: ERR[ FW ]Failed to load firmware wil6210.fw
Obrigado por qualquer sugestão, mg