Meu Adata HV 100 não aparece nos computadores; qualquer computador. Estou totalmente frustrado. Não aparece no sistema operacional Windows, Linux ou Mac.
Eu corri a maior parte do comando que encontrei, mas nenhum deles funcionou. Aqui está a saída para dmesg antes de ligar meu HDD:
[27136.937677] usb 1-2: new high-speed USB device number 11 using xhci_hcd
[27137.106486] usb 1-2: New USB device found, idVendor=125f, idProduct=a42a
[27137.106488] usb 1-2: New USB device strings: Mfr=1, Product=2, SerialNumber=3
[27137.106490] usb 1-2: Product: HV100
[27137.106491] usb 1-2: Manufacturer: ADATA
[27137.106492] usb 1-2: SerialNumber: 4681241C3115
[27137.106867] usb-storage 1-2:1.0: USB Mass Storage device detected
[27137.107524] scsi host2: usb-storage 1-2:1.0
[27138.125899] scsi 2:0:0:0: Direct-Access ADATA HV100 9102 PQ: 0 ANSI: 6
[27138.126165] sd 2:0:0:0: Attached scsi generic sg2 type 0
[27138.127058] sd 2:0:0:0: [sdb] Spinning up disk...
[27139.149519] .
[27140.173609] .
[27141.197376] .
[27142.221304] .
[27149.389636] not responding...
[27329.381149] sd 2:0:0:0: timing out command, waited 180s
[27509.378184] sd 2:0:0:0: timing out command, waited 180s
[27648.266603] usb 1-2: USB disconnect, device number 11
[27648.281974] sd 2:0:0:0: [sdb] Read Capacity(10) failed: Result: hostbyte=DID_NO_CONNECT driverbyte=DRIVER_OK
[27648.281977] sd 2:0:0:0: [sdb] Sense not available.
[27648.281981] sd 2:0:0:0: [sdb] 0 512-byte logical blocks: (0 B/0 B)
[27648.281983] sd 2:0:0:0: [sdb] 0-byte physical blocks
[27648.282006] sd 2:0:0:0: [sdb] Write Protect is on
[27648.282008] sd 2:0:0:0: [sdb] Mode Sense: 00 30 f8 ec
[27648.282023] sd 2:0:0:0: [sdb] Asking for cache data failed
[27648.282027] sd 2:0:0:0: [sdb] Assuming drive cache: write through
[27648.282230] sd 2:0:0:0: [sdb] Read Capacity(10) failed: Result: hostbyte=DID_NO_CONNECT driverbyte=DRIVER_OK
[27648.282232] sd 2:0:0:0: [sdb] Sense not available.
[27648.282291] sd 2:0:0:0: [sdb] Attached SCSI disk
E depois que eu conectei meu HDD:
Direct-Access ADATA HV100 9102 PQ: 0 ANSI: 6
[27138.126165] sd 2:0:0:0: Attached scsi generic sg2 type 0
[27138.127058] sd 2:0:0:0: [sdb] Spinning up disk...
[27139.149519] .[27148.364869] .
[27149.388800] .
[27149.389636] not responding...
[27329.381149] sd 2:0:0:0: timing out command, waited 180
[27648.266603] usb 1-2: USB disconnect, device number 11
[27648.281974] sd 2:0:0:0: [sdb] Read Capacity(10) failed: Result: hostbyte=DID_NO_CONNECT driverbyte=DRIVER_OK
[27648.281977] sd 2:0:0:0: [sdb] Sense not available.
[27648.281981] sd 2:0:0:0: [sdb] 0 512-byte logical blocks: (0 B/0 B)
[27648.281983] sd 2:0:0:0: [sdb] 0-byte physical blocks
[27648.282006] sd 2:0:0:0: [sdb] Write Protect is on
[27648.282008] sd 2:0:0:0: [sdb] Mode Sense: 00 30 f8 ec
[27648.282023] sd 2:0:0:0: [sdb] Asking for cache data failed
[27648.282027] sd 2:0:0:0: [sdb] Assuming drive cache: write through
[27648.282230] sd 2:0:0:0: [sdb] Read Capacity(10) failed: Result: hostbyte=DID_NO_CONNECT driverbyte=DRIVER_OK
[27648.282232] sd 2:0:0:0: [sdb] Sense not available.
[27648.282291] sd 2:0:0:0: [sdb] Attached SCSI disk
[27796.373883] usb 1-2: new high-speed USB device number 12 using xhci_hcd
[27796.554715] usb 1-2: New USB device found, idVendor=125f, idProduct=a42a
[27796.554718] usb 1-2: New USB device strings: Mfr=1, Product=2, SerialNumber=3
[27796.554719] usb 1-2: Product: HV100
[27796.554721] usb 1-2: Manufacturer: ADATA
[27796.554723] usb 1-2: SerialNumber: 4681241C3115
[27796.555787] usb-storage 1-2:1.0: USB Mass Storage device detected
[27796.555914] scsi host2: usb-storage 1-2:1.0
[27797.574152] scsi 2:0:0:0: Direct-Access ADATA HV100 9102 PQ: 0 ANSI: 6
[27797.574416] sd 2:0:0:0: Attached scsi generic sg2 type 0
[27797.576055] sd 2:0:0:0: [sdb] Spinning up disk...
[27818.052724] .
[27897.920532] not responding...
[27909.919829] sd 2:0:0:0: [sdb] Read Capacity(10) failed: Result: hostbyte=DID_OK driverbyte=DRIVER_SENSE
[27909.919833] sd 2:0:0:0: [sdb] Sense Key : Not Ready [current]
[27909.919835] sd 2:0:0:0: [sdb] Add. Sense: Logical unit is in process of becoming ready
[27909.919839] sd 2:0:0:0: [sdb] 0 512-byte logical blocks: (0 B/0 B)
[27909.919841] sd 2:0:0:0: [sdb] 0-byte physical blocks
[27911.919622] sd 2:0:0:0: [sdb] Test WP failed, assume Write Enabled
[27913.919517] sd 2:0:0:0: [sdb] Asking for cache data failed
[27913.919523] sd 2:0:0:0: [sdb] Assuming drive cache: write through
[27913.923086] sd 2:0:0:0: [sdb] Spinning up disk...
[27914.943645] .
[279864004] .
[27986.587944] .
[27986.588779] not responding...
[28166.595194] sd 2:0:0:0: timing out command, waited 180s
[28346.598318] sd 2:0:0:0: timing out command, waited 180s
[28526.597690] sd 2:0:0:0: timing out command, waited 180s
[28526.597709] sd 2:0:0:0: [sdb] Read Capacity(10) failed: Result: hostbyte=DID_OK driverbyte=DRIVER_SENSE
[28526.597711] sd 2:0:0:0: [sdb] Sense Key : Hardware Error [current]
[28526.597714] sd 2:0:0:0: [sdb] ASC=0x44 <<vendor>>ASCQ=0x81
O disco rígido aparece, mas para em " Disco giratório "
SAÍDA PARA lsblk é:
saroj@saroj-HP-Notebook:~$ lsblk
NAME MAJ:MIN RM SIZE RO TYPE MOUNTPOINT
loop1 7:1 0 82M 1 loop /snap/core/4327
loop8 7:8 0 81.7M 1 loop /snap/core/4206
loop6 7:6 0 192.2M 1 loop /snap/hiri/42
loop4 7:4 0 81.6M 1 loop /snap/core/4110
sr0 11:0 1 1024M 0 rom
loop2 7:2 0 180.5M 1 loop /snap/vlc/190
loop0 7:0 0 125.6M 1 loop /snap/obs-studio/3
sda 8:0 0 931.5G 0 disk
├─sda4 8:4 0 331.5G 0 part /media/Softwares
├─sda2 8:2 0 300G 0 part /media/Multimedia
├─sda3 8:3 0 100G 0 part /media/saroj/Documents 1GB
└─sda1 8:1 0 199.5G 0 part /
loop7 7:7 0 93.5M 1 loop /snap/slack/5
loop5 7:5 0 162.6M 1 loop /snap/spotify/6
loop3 7:3 0 93.5M 1 loop /snap/slack/6
OBRIGADO COM ANTECEDÊNCIA.