Você precisa usar o driver r8168-dkms e desativar secure boot no seu BIOS.
Você também precisará verificar se está usando um bom cabo ethernet e switch / hub (se estiver usando um).
Após a atualização do Kubuntu 16.04 LTS para 16.10, a conexão com fio não funciona. A conexão com fio é exibida no Network Manager, mas não é possível selecionar o botão "Conectar". A conexão wi-fi está funcionando.
O mais estranho é que usando um Kubuntu 16.10 live USB no mesmo PC, a conexão ethernet é reconhecida e funcionando imediatamente.
Estes são alguns resultados:
*-network
description: Wireless interface
product: Wireless 7260
vendor: Intel Corporation
physical id: 0
bus info: pci@0000:02:00.0
logical name: wlan0
version: 73
serial: a0:a8:cd:cc:e2:7d
width: 64 bits
clock: 33MHz
capabilities: pm msi pciexpress bus_master cap_list ethernet physical wireless
configuration: broadcast=yes driver=iwlwifi driverversion=4.8.0-37-generic firmware=17.352738.0 ip=192.168.178.32 latency=0 link=yes multic
ast=yes wireless=IEEE 802.11
resources: irq:93 memory:d0700000-d0701fff
*-network DISABLED
description: Ethernet interface
product: RTL8111/8168/8411 PCI Express Gigabit Ethernet Controller
vendor: Realtek Semiconductor Co., Ltd.
physical id: 0
bus info: pci@0000:03:00.0
logical name: eth0
version: 0c
serial: c0:3f:d5:6d:86:9e
size: 10Mbit/s
capacity: 1Gbit/s
width: 64 bits
clock: 33MHz
capabilities: pm msi pciexpress msix vpd bus_master cap_list ethernet physical tp mii 10bt 10bt-fd 100bt 100bt-fd 1000bt 1000bt-fd autonego
tiation
configuration: autonegotiation=on broadcast=yes driver=r8169 driverversion=2.3LK-NAPI duplex=full latency=0 link=no multicast=yes port=MII
speed=10Mbit/s
resources: irq:89 ioport:e000(size=256) memory:d0604000-d0604fff memory:d0600000-d0603fff
andrea@Sara-desktop:~$
[code]sudo ifconfig -a[/code]
eth0: flags=4098<BROADCAST,MULTICAST> mtu 1500
ether c0:3f:d5:6d:86:9e txqueuelen 1000 (Ethernet)
RX packets 0 bytes 0 (0.0 B)
RX errors 0 dropped 0 overruns 0 frame 0
TX packets 0 bytes 0 (0.0 B)
TX errors 0 dropped 0 overruns 0 carrier 0 collisions 0
lo: flags=73<UP,LOOPBACK,RUNNING> mtu 65536
inet 127.0.0.1 netmask 255.0.0.0
inet6 ::1 prefixlen 128 scopeid 0x10<host>
loop txqueuelen 1 (Loopback locale)
RX packets 2060 bytes 181968 (181.9 KB)
RX errors 0 dropped 0 overruns 0 frame 0
TX packets 2060 bytes 181968 (181.9 KB)
TX errors 0 dropped 0 overruns 0 carrier 0 collisions 0
wlan0: flags=4163<UP,BROADCAST,RUNNING,MULTICAST> mtu 1500
inet 192.168.178.32 netmask 255.255.255.0 broadcast 192.168.178.255
inet6 fe80::a2a8:cdff:fecc:e27d prefixlen 64 scopeid 0x20<link>
ether a0:a8:cd:cc:e2:7d txqueuelen 1000 (Ethernet)
RX packets 39431 bytes 53149953 (53.1 MB)
RX errors 0 dropped 0 overruns 0 frame 0
TX packets 11174 bytes 1144582 (1.1 MB)
TX errors 0 dropped 0 overruns 0 carrier 0 collisions 0
ifconfig -a
eth0: flags=4098<BROADCAST,MULTICAST> mtu 1500
ether c0:3f:d5:6d:86:9e txqueuelen 1000 (Ethernet)
RX packets 0 bytes 0 (0.0 B)
RX errors 0 dropped 0 overruns 0 frame 0
TX packets 0 bytes 0 (0.0 B)
TX errors 0 dropped 0 overruns 0 carrier 0 collisions 0
lo: flags=73<UP,LOOPBACK,RUNNING> mtu 65536
inet 127.0.0.1 netmask 255.0.0.0
inet6 ::1 prefixlen 128 scopeid 0x10<host>
loop txqueuelen 1 (Loopback locale)
RX packets 43498 bytes 2940360 (2.9 MB)
RX errors 0 dropped 0 overruns 0 frame 0
TX packets 43498 bytes 2940360 (2.9 MB)
TX errors 0 dropped 0 overruns 0 carrier 0 collisions 0
wlan0: flags=4098<BROADCAST,MULTICAST> mtu 1500
ether a0:a8:cd:cc:e2:7d txqueuelen 1000 (Ethernet)
RX packets 0 bytes 0 (0.0 B)
RX errors 0 dropped 0 overruns 0 frame 0
TX packets 0 bytes 0 (0.0 B)
TX errors 0 dropped 0 overruns 0 carrier 0 collisions 0
Seguindo algumas sugestões eu carreguei o driver r8168 ao invés do r8169, sem sucesso. O PC é um NUC DN2820FYK.
Agradecemos antecipadamente por sua ajuda.
Este é o resultado do comando sugerido:
dmesg | grep r8168
[ 1.614987] r8168: loading out-of-tree module taints kernel.
[ 1.615409] r8168: module verification failed: signature and/or required key missing - tainting kernel
[ 1.615988] r8168 Gigabit Ethernet driver 8.042.00-NAPI loaded
[ 1.637921] r8168: This product is covered by one or more of the following patents: US6,570,884, US6,115,776, and US6,327,625.
[ 1.637930] r8168 Copyright (C) 2016 Realtek NIC software team <[email protected]>
[ 1.722440] r8168 0000:03:00.0 enp3s0: renamed from eth0
Você precisa usar o driver r8168-dkms e desativar secure boot no seu BIOS.
Você também precisará verificar se está usando um bom cabo ethernet e switch / hub (se estiver usando um).
Depois de atualizar para o Ubuntu 17.04 e ler este tópico, consegui corrigir minha conexão Ethernet (eth0).
No arquivo: /usr/lib/NetworkManager/conf.d/10-globally-managed-devices.conf
Eu adicionei ", exceto: type: eth0" (sem as aspas) ao final da linha. (Você vai notar também diz exceto: tipo: wifi e exceto: tipo: wwan)
Finalmente eu criei o arquivo /etc/NetworkManager/conf.d/10-globally-managed-devices.conf usando o sudo touch /etc/NetworkManager/conf.d/10-globally-managed-devices.conf
Esqueci-me de como reiniciar o serviço, por isso reiniciei. Ethernet fixa.
Espero que isso ajude.