Eu emiti o comando dd para zerar meu disco rígido. O comando foi concluído com sucesso, mas somente parte do disco rígido foi sobrescrito:
mint@mint ~ $ sudo dd if=/dev/zero of=/dev/sda
dd: writing to ‘/dev/sda’: Input/output error
258416001+0 records in
258416000+0 records out
132308992000 bytes (132 GB) copied, 3741.09 s, 35.4 MB/s
O seguinte mostra a configuração do disco rígido:
mint@mint ~ $ sudo fdisk -l /dev/sda
Disk /dev/sda: 320.1 GB, 320072933376 bytes
255 heads, 63 sectors/track, 38913 cylinders, total 625142448 sectors
Units = sectors of 1 * 512 = 512 bytes
Sector size (logical/physical): 512 bytes / 512 bytes
I/O size (minimum/optimal): 512 bytes / 512 bytes
Disk identifier: 0x8f45867a
Device Boot Start End Blocks Id System
Notas:
smartctl output:
mint@mint ~ $ sudo smartctl -a /dev/sda
smartctl 6.2 2013-07-26 r3841 [x86_64-linux-3.13.0-37-generic] (local build)
Copyright (C) 2002-13, Bruce Allen, Christian Franke, www.smartmontools.org
=== START OF INFORMATION SECTION ===
Model Family: Western Digital Scorpio Black
Device Model: WDC WD3200BEKT-75PVMT0
Serial Number: WD-WXC1A2127646
LU WWN Device Id: 5 0014ee 6abb45855
Firmware Version: 01.01A01
User Capacity: 320,072,933,376 bytes [320 GB]
Sector Size: 512 bytes logical/physical
Rotation Rate: 7200 rpm
Device is: In smartctl database [for details use: -P show]
ATA Version is: ATA8-ACS (minor revision not indicated)
SATA Version is: SATA 2.6, 3.0 Gb/s
Local Time is: Sat Jun 13 05:27:23 2015 UTC
SMART support is: Available - device has SMART capability.
SMART support is: Enabled
=== START OF READ SMART DATA SECTION ===
SMART overall-health self-assessment test result: FAILED!
Drive failure expected in less than 24 hours. SAVE ALL DATA.
See vendor-specific Attribute list for failed Attributes.
General SMART Values:
Offline data collection status: (0x00) Offline data collection activity
was never started.
Auto Offline Data Collection: Disabled.
Self-test execution status: ( 0) The previous self-test routine completed
without error or no self-test has ever
been run.
Total time to complete Offline
data collection: ( 5760) seconds.
Offline data collection
capabilities: (0x7b) SMART execute Offline immediate.
Auto Offline data collection on/off support.
Suspend Offline collection upon new
command.
Offline surface scan supported.
Self-test supported.
Conveyance Self-test supported.
Selective Self-test supported.
SMART capabilities: (0x0003) Saves SMART data before entering
power-saving mode.
Supports SMART auto save timer.
Error logging capability: (0x01) Error logging supported.
General Purpose Logging supported.
Short self-test routine
recommended polling time: ( 2) minutes.
Extended self-test routine
recommended polling time: ( 60) minutes.
Conveyance self-test routine
recommended polling time: ( 5) minutes.
SCT capabilities: (0x7035) SCT Status supported.
SCT Feature Control supported.
SCT Data Table supported.
SMART Attributes Data Structure revision number: 16
Vendor Specific SMART Attributes with Thresholds:
ID# ATTRIBUTE_NAME FLAG VALUE WORST THRESH TYPE UPDATED WHEN_FAILED RAW_VALUE
1 Raw_Read_Error_Rate 0x002f 200 200 051 Pre-fail Always - 0
3 Spin_Up_Time 0x0027 163 160 021 Pre-fail Always - 816
4 Start_Stop_Count 0x0032 099 099 000 Old_age Always - 1156
5 Reallocated_Sector_Ct 0x0033 133 133 140 Pre-fail Always FAILING_NOW 561
7 Seek_Error_Rate 0x002e 100 253 000 Old_age Always - 0
9 Power_On_Hours 0x0032 073 073 000 Old_age Always - 19736
10 Spin_Retry_Count 0x0032 100 100 000 Old_age Always - 0
11 Calibration_Retry_Count 0x0032 100 100 000 Old_age Always - 0
12 Power_Cycle_Count 0x0032 099 099 000 Old_age Always - 1151
191 G-Sense_Error_Rate 0x0032 001 001 000 Old_age Always - 2733
192 Power-Off_Retract_Count 0x0032 200 200 000 Old_age Always - 64
193 Load_Cycle_Count 0x0032 137 137 000 Old_age Always - 191394
194 Temperature_Celsius 0x0022 105 090 000 Old_age Always - 38
196 Reallocated_Event_Count 0x0032 194 194 000 Old_age Always - 6
197 Current_Pending_Sector 0x0032 200 200 000 Old_age Always - 0
198 Offline_Uncorrectable 0x0030 100 253 000 Old_age Offline - 0
199 UDMA_CRC_Error_Count 0x0032 200 200 000 Old_age Always - 0
200 Multi_Zone_Error_Rate 0x0008 100 253 000 Old_age Offline - 0
240 Head_Flying_Hours 0x0032 074 074 000 Old_age Always - 19078
241 Total_LBAs_Written 0x0032 200 200 000 Old_age Always - 37643305479
242 Total_LBAs_Read 0x0032 200 200 000 Old_age Always - 31320890404
254 Free_Fall_Sensor 0x0032 197 197 000 Old_age Always - 3
SMART Error Log Version: 1
ATA Error Count: 48 (device log contains only the most recent five errors)
CR = Command Register [HEX]
FR = Features Register [HEX]
SC = Sector Count Register [HEX]
SN = Sector Number Register [HEX]
CL = Cylinder Low Register [HEX]
CH = Cylinder High Register [HEX]
DH = Device/Head Register [HEX]
DC = Device Command Register [HEX]
ER = Error register [HEX]
ST = Status register [HEX]
Powered_Up_Time is measured from power on, and printed as
DDd+hh:mm:SS.sss where DD=days, hh=hours, mm=minutes,
SS=sec, and sss=millisec. It "wraps" after 49.710 days.
Error 48 occurred at disk power-on lifetime: 19723 hours (821 days + 19 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
01 51 08 81 1d 67 ef Error: AMNF 8 sectors at LBA = 0x0f671d81 = 258416001
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
c8 00 08 80 1d 67 ef 00 00:36:32.852 READ DMA
ef 10 02 00 00 00 a0 00 00:36:32.852 SET FEATURES [Enable SATA feature]
ec 00 00 00 00 00 a0 00 00:36:32.850 IDENTIFY DEVICE
ef 03 46 00 00 00 a0 00 00:36:32.850 SET FEATURES [Set transfer mode]
Error 47 occurred at disk power-on lifetime: 19723 hours (821 days + 19 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
40 51 08 81 1d 67 ef Error: UNC 8 sectors at LBA = 0x0f671d81 = 258416001
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
c8 00 08 80 1d 67 ef 00 00:36:31.120 READ DMA
ef 10 02 00 00 00 a0 00 00:36:31.119 SET FEATURES [Enable SATA feature]
ec 00 00 00 00 00 a0 00 00:36:31.118 IDENTIFY DEVICE
ef 03 46 00 00 00 a0 00 00:36:31.118 SET FEATURES [Set transfer mode]
Error 46 occurred at disk power-on lifetime: 19723 hours (821 days + 19 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
40 51 08 81 1d 67 ef Error: UNC 8 sectors at LBA = 0x0f671d81 = 258416001
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
c8 00 08 80 1d 67 ef 00 00:36:29.389 READ DMA
ef 10 02 00 00 00 a0 00 00:36:29.389 SET FEATURES [Enable SATA feature]
ec 00 00 00 00 00 a0 00 00:36:29.387 IDENTIFY DEVICE
ef 03 46 00 00 00 a0 00 00:36:29.387 SET FEATURES [Set transfer mode]
Error 45 occurred at disk power-on lifetime: 19723 hours (821 days + 19 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
40 51 08 81 1d 67 ef Error: UNC 8 sectors at LBA = 0x0f671d81 = 258416001
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
c8 00 08 80 1d 67 ef 00 00:36:27.657 READ DMA
ef 10 02 00 00 00 a0 00 00:36:27.657 SET FEATURES [Enable SATA feature]
ec 00 00 00 00 00 a0 00 00:36:27.655 IDENTIFY DEVICE
ef 03 46 00 00 00 a0 00 00:36:27.655 SET FEATURES [Set transfer mode]
Error 44 occurred at disk power-on lifetime: 19723 hours (821 days + 19 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
40 51 08 81 1d 67 ef Error: UNC 8 sectors at LBA = 0x0f671d81 = 258416001
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
c8 00 08 80 1d 67 ef 00 00:36:25.926 READ DMA
ef 10 02 00 00 00 a0 00 00:36:25.926 SET FEATURES [Enable SATA feature]
ec 00 00 00 00 00 a0 00 00:36:25.924 IDENTIFY DEVICE
ef 03 46 00 00 00 a0 00 00:36:25.924 SET FEATURES [Set transfer mode]
SMART Self-test log structure revision number 1
Num Test_Description Status Remaining LifeTime(hours) LBA_of_first_error
# 1 Short offline Completed without error 00% 8 -
# 2 Short offline Completed without error 00% 8 -
# 3 Short offline Completed without error 00% 8 -
# 4 Short offline Completed without error 00% 8 -
# 5 Short offline Completed without error 00% 8 -
# 6 Short offline Completed without error 00% 8 -
# 7 Short offline Completed without error 00% 7 -
# 8 Short offline Completed without error 00% 7 -
# 9 Short offline Completed without error 00% 1 -
#10 Short offline Completed without error 00% 1 -
#11 Short offline Completed without error 00% 1 -
#12 Short offline Completed without error 00% 1 -
#13 Short offline Completed without error 00% 1 -
#14 Short offline Completed without error 00% 1 -
#15 Short offline Completed without error 00% 1 -
#16 Short offline Completed without error 00% 1 -
SMART Selective self-test log data structure revision number 1
SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS
1 0 0 Not_testing
2 0 0 Not_testing
3 0 0 Not_testing
4 0 0 Not_testing
5 0 0 Not_testing
Selective self-test flags (0x0):
After scanning selected spans, do NOT read-scan remainder of disk.
If Selective self-test is pending on power-up, resume after 0 minute delay.
dd output indica claramente que ocorreu um erro de E / S. Provavelmente o disco subjacente é incapaz de realocar um setor de reposição, ou ele falhou de uma maneira irrecuperável (por exemplo: perda de link SATA).
Faça uma tentativa com o ddrescue, emitindo o seguinte comando: ddrescue /dev/zero /dev/sda -f -D . Isso muda alguma coisa?
Eu vi a mesma coisa acontecer devido a gravações que passam pelo cache. Por padrão, dd faz write chamadas do sistema 512 bytes por vez. Isso passa por uma camada de cache operando com blocos de 4096 bytes. Mas a mídia subjacente ainda usa setores de 512 bytes.
Portanto, quando dd faz uma chamada de sistema write , o kernel carregará o bloco de 4096 bytes do disco para alterar os 512 bytes e gravá-lo de volta. Quando isso acontece é a etapa de leitura que falha, então o kernel nunca chega à etapa de escrita.
A maneira que tenho andado por aí é ignorar o cache. A especificação de oflag=direct ignora a camada de armazenamento em cache das operações de gravação. Como isso pode causar uma redução significativa no desempenho, usei-o apenas para gravar o único setor defeituoso usando seek= (deslocamento) e count=1 .
Para forçar o dd a ignorar os erros:
dd if=/dev/zero of=/dev/sda conv=noerror,sync
Como alternativa, use o ddrescue, que tem esse comportamento como padrão.
Tags hard-drive dd