Barracuda 7200.12 fazendo um som muito alto (squeak). O Drive não está sendo exibido

0

Eu tenho um Barracuda 7200.12 1TB, a unidade não está sendo detectada por nenhum sistema operacional, antes de girar os discos eu mesmo que o disco rígido faria um clique como se as cabeças estivessem tentando se mover, mas os pratos não estão girando e um som de apito baixo.

Depois que eu abri o disco rígido, forcei-o a girar em câmera lenta e depois decolou. a partir daí, o barulho estranho veio alto.

Eu só acho que o prato está desalinhado, o que é um grande problema :) anexado é um vídeo para esse som.

link

Agora, depois de apertar os parafusos, como David sugeriu. Eu consegui ver o disco na minha lista de discos duas vezes. abaixo está o log do dmesg.

[  986.211268] sd 1:0:0:0: Attached scsi generic sg1 type 0
[  986.211651] sd 1:0:0:0: [sdb] 1953525168 512-byte logical blocks: (1.00 TB/932 GiB)
[  986.211947] sd 1:0:0:0: [sdb] Write Protect is off
[  986.211952] sd 1:0:0:0: [sdb] Mode Sense: 28 00 00 00
[  986.212325] sd 1:0:0:0: [sdb] No Caching mode page found
[  986.212335] sd 1:0:0:0: [sdb] Assuming drive cache: write through
[ 1016.704426] usb 1-1: reset high-speed USB device number 8 using xhci_hcd
[ 1049.430537] usb 1-1: reset high-speed USB device number 8 using xhci_hcd
[ 1060.550003] usb 1-1: USB disconnect, device number 8
[ 1060.550028] sd 1:0:0:0: Device offlined - not ready after error recovery
[ 1060.550043] sd 1:0:0:0: [sdb] tag#0 FAILED Result: hostbyte=DID_ABORT driverbyte=DRIVER_OK
[ 1060.550048] sd 1:0:0:0: [sdb] tag#0 CDB: Read(10) 28 00 00 00 00 00 00 00 08 00
[ 1060.550052] blk_update_request: I/O error, dev sdb, sector 0
[ 1060.550061] Buffer I/O error on dev sdb, logical block 0, async page read
[ 1060.550120] sd 1:0:0:0: rejecting I/O to offline device
[ 1060.550143] ldm_validate_partition_table(): Disk read failed.
[ 1060.550176] Dev sdb: unable to read RDB block 0
[ 1060.550226]  sdb: unable to read partition table
[ 1060.550597] sd 1:0:0:0: [sdb] Read Capacity(10) failed: Result: hostbyte=DID_NO_CONNECT driverbyte=DRIVER_OK
[ 1060.550600] sd 1:0:0:0: [sdb] Sense not available.
[ 1060.550605] sd 1:0:0:0: [sdb] 0 512-byte logical blocks: (0 B/0 B)
[ 1060.550629] sd 1:0:0:0: [sdb] Attached SCSI disk
[ 1911.705428] usb 1-1: new high-speed USB device number 9 using xhci_hcd
[ 1911.846722] usb 1-1: New USB device found, idVendor=152d, idProduct=2338
[ 1911.846727] usb 1-1: New USB device strings: Mfr=1, Product=2, SerialNumber=5
[ 1911.846730] usb 1-1: Product: USB to ATA/ATAPI bridge
[ 1911.846732] usb 1-1: Manufacturer: JMicron
[ 1911.846734] usb 1-1: SerialNumber: 000000000000
[ 1911.847857] usb-storage 1-1:1.0: USB Mass Storage device detected
[ 1911.848150] scsi host1: usb-storage 1-1:1.0
[ 1912.878129] scsi 1:0:0:0: Direct-Access     ST310005 28AS                  PQ: 0 ANSI: 5
[ 1912.878875] sd 1:0:0:0: [sdb] 1953525168 512-byte logical blocks: (1.00 TB/932 GiB)
[ 1912.878927] sd 1:0:0:0: Attached scsi generic sg1 type 0
[ 1912.879139] sd 1:0:0:0: [sdb] Write Protect is off
[ 1912.879142] sd 1:0:0:0: [sdb] Mode Sense: 28 00 00 00
[ 1912.879425] sd 1:0:0:0: [sdb] No Caching mode page found
[ 1912.879431] sd 1:0:0:0: [sdb] Assuming drive cache: write through
[ 1944.367889] usb 1-1: reset high-speed USB device number 9 using xhci_hcd
[ 1977.122025] usb 1-1: reset high-speed USB device number 9 using xhci_hcd
[ 1988.265153] sd 1:0:0:0: Device offlined - not ready after error recovery
[ 1988.265173] sd 1:0:0:0: [sdb] tag#0 FAILED Result: hostbyte=DID_ABORT driverbyte=DRIVER_OK
[ 1988.265180] sd 1:0:0:0: [sdb] tag#0 CDB: Read(10) 28 00 00 00 00 00 00 00 08 00
[ 1988.265184] blk_update_request: I/O error, dev sdb, sector 0
[ 1988.265188] usb 1-1: USB disconnect, device number 9
[ 1988.265197] Buffer I/O error on dev sdb, logical block 0, async page read
[ 1988.265250] sd 1:0:0:0: rejecting I/O to offline device
[ 1988.265274] sd 1:0:0:0: rejecting I/O to offline device
[ 1988.265281] ldm_validate_partition_table(): Disk read failed.
[ 1988.265290] sd 1:0:0:0: rejecting I/O to offline device
[ 1988.265301] sd 1:0:0:0: rejecting I/O to offline device
[ 1988.265312] sd 1:0:0:0: rejecting I/O to offline device
[ 1988.265323] sd 1:0:0:0: rejecting I/O to offline device
[ 1988.265329] Dev sdb: unable to read RDB block 0
[ 1988.265338] sd 1:0:0:0: rejecting I/O to offline device
[ 1988.265349] sd 1:0:0:0: rejecting I/O to offline device
[ 1988.265387]  sdb: unable to read partition table
[ 1988.267016] sd 1:0:0:0: [sdb] Read Capacity(10) failed: Result: hostbyte=DID_NO_CONNECT driverbyte=DRIVER_OK
[ 1988.267022] sd 1:0:0:0: [sdb] Sense not available.
[ 1988.267032] sd 1:0:0:0: [sdb] 0 512-byte logical blocks: (0 B/0 B)
[ 1988.267075] sd 1:0:0:0: [sdb] Attached SCSI disk
[ 2167.158983] usb 1-1: new high-speed USB device number 10 using xhci_hcd
[ 2167.300232] usb 1-1: New USB device found, idVendor=152d, idProduct=2338
[ 2167.300237] usb 1-1: New USB device strings: Mfr=1, Product=2, SerialNumber=5
[ 2167.300240] usb 1-1: Product: USB to ATA/ATAPI bridge
[ 2167.300242] usb 1-1: Manufacturer: JMicron
[ 2167.300244] usb 1-1: SerialNumber: 000000000000
[ 2167.301229] usb-storage 1-1:1.0: USB Mass Storage device detected
[ 2167.301516] scsi host1: usb-storage 1-1:1.0
[ 2168.319867] scsi 1:0:0:0: Direct-Access     ST310005 28AS                  PQ: 0 ANSI: 5
[ 2168.321028] sd 1:0:0:0: Attached scsi generic sg1 type 0
[ 2168.321243] sd 1:0:0:0: [sdb] 1953525168 512-byte logical blocks: (1.00 TB/932 GiB)
[ 2168.321571] sd 1:0:0:0: [sdb] Write Protect is off
[ 2168.321577] sd 1:0:0:0: [sdb] Mode Sense: 28 00 00 00
[ 2168.321863] sd 1:0:0:0: [sdb] No Caching mode page found
[ 2168.321875] sd 1:0:0:0: [sdb] Assuming drive cache: write through
[ 2200.381339] usb 1-1: reset high-speed USB device number 10 using xhci_hcd
[ 2233.107466] usb 1-1: reset high-speed USB device number 10 using xhci_hcd
[ 2244.250856] sd 1:0:0:0: Device offlined - not ready after error recovery
[ 2244.250860] usb 1-1: USB disconnect, device number 10
[ 2244.250875] sd 1:0:0:0: [sdb] tag#0 FAILED Result: hostbyte=DID_ABORT driverbyte=DRIVER_OK
[ 2244.250881] sd 1:0:0:0: [sdb] tag#0 CDB: Read(10) 28 00 00 00 00 00 00 00 08 00
[ 2244.250884] blk_update_request: I/O error, dev sdb, sector 0
[ 2244.250894] Buffer I/O error on dev sdb, logical block 0, async page read
[ 2244.250949] sd 1:0:0:0: rejecting I/O to offline device
[ 2244.250969] sd 1:0:0:0: rejecting I/O to offline device
[ 2244.250975] ldm_validate_partition_table(): Disk read failed.
[ 2244.251008] Dev sdb: unable to read RDB block 0
[ 2244.251059]  sdb: unable to read partition table
[ 2244.251470] sd 1:0:0:0: [sdb] Read Capacity(10) failed: Result: hostbyte=DID_NO_CONNECT driverbyte=DRIVER_OK
[ 2244.251474] sd 1:0:0:0: [sdb] Sense not available.
[ 2244.251484] sd 1:0:0:0: [sdb] 0 512-byte logical blocks: (0 B/0 B)
[ 2244.251525] sd 1:0:0:0: [sdb] Attached SCSI disk

abaixo de lsusb -v

Bus 001 Device 011: ID 152d:2338 JMicron Technology Corp. / JMicron USA Technology Corp. JM20337 Hi-Speed USB to SATA & PATA Combo Bridge
Couldn't open device, some information will be missing

Device Descriptor:
  bLength                18
  bDescriptorType         1
  bcdUSB               2.00
  bDeviceClass            0 (Defined at Interface level)
  bDeviceSubClass         0 
  bDeviceProtocol         0 
  bMaxPacketSize0        64
  idVendor           0x152d JMicron Technology Corp. / JMicron USA Technology Corp.
  idProduct          0x2338 JM20337 Hi-Speed USB to SATA & PATA Combo Bridge
  bcdDevice            1.00
  iManufacturer           1 
  iProduct                2 
  iSerial                 5 
  bNumConfigurations      1
  Configuration Descriptor:
    bLength                 9
    bDescriptorType         2
    wTotalLength           32
    bNumInterfaces          1
    bConfigurationValue     1
    iConfiguration          4 
    bmAttributes         0xc0
      Self Powered
    MaxPower                2mA
    Interface Descriptor:
      bLength                 9
      bDescriptorType         4
      bInterfaceNumber        0
      bAlternateSetting       0
      bNumEndpoints           2
      bInterfaceClass         8 Mass Storage
      bInterfaceSubClass      6 SCSI
      bInterfaceProtocol     80 Bulk-Only
      iInterface              6 
      Endpoint Descriptor:
        bLength                 7
        bDescriptorType         5
        bEndpointAddress     0x81  EP 1 IN
        bmAttributes            2
          Transfer Type            Bulk
          Synch Type               None
          Usage Type               Data
        wMaxPacketSize     0x0200  1x 512 bytes
        bInterval               0
      Endpoint Descriptor:
        bLength                 7
        bDescriptorType         5
        bEndpointAddress     0x02  EP 2 OUT
        bmAttributes            2
          Transfer Type            Bulk
          Synch Type               None
          Usage Type               Data
        wMaxPacketSize     0x0200  1x 512 bytes
        bInterval               0
    
por Waheed 02.09.2017 / 09:23

1 resposta

0

No seu vídeo, vejo que a parte superior da unidade está desativada. Ignorando meus comentários anteriores sobre poeira (que eu ainda aguardo - e de fato rodar o disco com os pratos expostos será ainda pior), a tampa da drivr é um elemento estrutural da unidade e precisa estar ligada com o torque correto nos parafusos - este vídeo do YouTube demonstra a importância do torque correto.

    
por 02.09.2017 / 15:44