Você terá que configurar vários SSIDs e atribuí-los a diferentes VLANs. 1 SSID será configurado para WPA e o outro para autenticação aberta. Então você terá que configurar o WEP nessa VLAN WEP.
Eu gostaria de configurar meu roteador Cisco 877w com dois SSIDs, WPA (atualmente trabalhando na minha configuração) e WEP.
Eu finalizei minha configuração atual no final desta pergunta, que está funcionando totalmente para o WPA .
Meu objetivo é ter:
Minha configuração
Current configuration : 3995 bytes
!
version 12.4
no service pad
service timestamps debug datetime msec
service timestamps log datetime msec
no service password-encryption
!
hostname CISCO877
!
boot-start-marker
boot-end-marker
!
logging buffered 51200 warnings
enable secret 5 xyz.
!
aaa new-model
!
aaa session-id common
!
crypto pki trustpoint TP-self-signed-240059495
enrollment selfsigned
subject-name cn=IOS-Self-Signed-Certificate-240059495
revocation-check none
rsakeypair TP-self-signed-240059495
!
!
dot11 syslog
!
dot11 ssid CISCO877
authentication open
authentication key-management wpa
guest-mode
wpa-psk ascii 0 1234567890
!
ip cef
no ip dhcp use vrf connected
ip dhcp excluded-address 10.2.1.0 10.2.1.10
ip dhcp excluded-address 10.2.1.200 10.2.1.254
!
ip dhcp pool lanpool
network 10.2.1.0 255.255.255.0
dns-server xxx.xxx.xxx.xxx xxx.xxx.xxx.xxx
default-router 10.2.1.1
lease 0 2
!
!
no ip domain lookup
ip domain name my.domain.com
ip name-server xxx.xxx.xxx.xxx
ip name-server xxx.xxx.xxx.xxx
!
!
!
username nick privilege 15 secret 5 xyz
!
!
archive
log config
hidekeys
!
!
ip ssh version 2
!
bridge irb
!
!
interface ATM0
mac-address 1111.2222.3333
no ip address
no ip redirects
no ip unreachables
no ip proxy-arp
no atm ilmi-keepalive
dsl operating-mode adsl2+
!
interface ATM0.1 point-to-point
description BE Broadband
ip address xxx.xxx.xxx.xxx 255.255.252.0
ip nat outside
ip virtual-reassembly
atm route-bridged ip
pvc 0/101
oam-pvc manage
encapsulation aal5snap
!
!
interface FastEthernet0
!
interface FastEthernet1
!
interface FastEthernet2
!
interface FastEthernet3
!
interface Dot11Radio0
description WIRELESS INTERFACE
no ip address
!
encryption mode ciphers tkip
!
encryption vlan 1 mode ciphers tkip
!
ssid CISCO877
!
speed basic-1.0 basic-2.0 basic-5.5 6.0 9.0 basic-11.0 12.0 18.0 24.0 36.0 48.0 54.0
station-role root
bridge-group 1
bridge-group 1 subscriber-loop-control
bridge-group 1 spanning-disabled
bridge-group 1 block-unknown-source
no bridge-group 1 source-learning
no bridge-group 1 unicast-flooding
!
interface Vlan1
description $ETH-SW-LAUNCH$$INTF-INFO-HWIC 4ESW$
no ip address
ip tcp adjust-mss 1452
bridge-group 1
!
interface BVI1
description Local Network
ip address 10.2.1.1 255.255.255.0
ip nat inside
ip virtual-reassembly
!
ip forward-protocol nd
ip route 0.0.0.0 0.0.0.0 xxx.xxx.xxx.xxx
!
no ip http server
no ip http secure-server
ip nat inside source static tcp 10.2.1.1 22 interface ATM0 22
ip nat inside source list 111 interface ATM0.1 overload
ip nat inside source static tcp 10.2.1.81 9000 interface ATM0.1 9000
ip nat inside source static tcp 10.2.1.81 3389 interface ATM0.1 3389
ip nat inside source static tcp 10.2.1.81 8182 interface ATM0.1 8182
ip nat inside source static tcp 10.2.1.81 80 interface ATM0.1 80
ip nat inside source static tcp 10.2.1.81 443 interface ATM0.1 443
!
access-list 1 permit any
access-list 99 permit 10.2.1.0 0.0.0.255
access-list 99 remark SSH Allowed Hosts
access-list 110 remark MYVPN TO REMOTEVPN
access-list 110 permit ip 10.2.1.0 0.0.0.255 192.168.13.0 0.0.0.255
access-list 111 deny ip 10.2.1.0 0.0.0.255 192.168.13.0 0.0.0.255
access-list 111 permit ip 10.2.1.0 0.0.0.255 any
no cdp run
!
!
!
control-plane
!
bridge 1 protocol ieee
bridge 1 route ip
banner exec ^C
!
line con 0
no modem enable
transport output telnet
line aux 0
transport output telnet
line vty 0 4
access-class 99 in
privilege level 15
transport input ssh
transport output none
!
scheduler max-task-time 5000
scheduler allocate 4000 1000
scheduler interval 500
end
Eu consultei a documentação sobre o conselho do wizlog aqui mas minha falta de experiência está me impedindo de implementar isso com a minha configuração atual.
Verifique o Capítulo 9 ( Configuração de uma conexão LAN sem fio ) do Guia de configuração do Cisco para obter instruções detalhadas sobre como configurar o seu roteador.
Passo 6 (9-3) e não se esqueça de verificar o seu exemplo.