Eu tenho um servidor onde atualizarei o firmware e os drivers dos controladores RAID da Adaptec em breve, e então eu estava no arcconf para verificar algumas coisas.
Os quatro discos são todos do mesmo modelo configurado como um volume RAID10. Ao executar o GETCONFIG do arcconf, fiquei um pouco surpreso que uma das unidades esteja rodando a 3.0gb / s em vez de 6, como as outras unidades.
Qual poderia ser a razão para isso, e existe uma maneira de fazê-lo funcionar a 6gb / s?
Controllers found: 1
----------------------------------------------------------------------
Controller information
----------------------------------------------------------------------
Controller Status : Optimal
Channel description : SAS/SATA
Controller Model : Adaptec 6805
Controller Serial Number :
Controller World Wide Name :
Controller Alarm : Enabled
Physical Slot : 1
Temperature : 54 C/ 129 F (Normal)
Installed memory : 512 MB
Global task priority : High
Performance Mode : Default/Dynamic
Host bus type : PCIe
Host bus speed : 5000 MHz
Host bus link width : 8 bit(s)/link(s)
Stayawake period : Disabled
Spinup limit internal drives : 0
Spinup limit external drives : 0
Defunct disk drive count : 0
Logical devices/Failed/Degraded : 1/0/0
NCQ status : Enabled
Statistics data collection mode : Enabled
--------------------------------------------------------
RAID Properties
--------------------------------------------------------
Copyback : Disabled
Background consistency check : Disabled
Background consistency check period : 30
Automatic Failover : Enabled
--------------------------------------------------------
Controller Version Information
--------------------------------------------------------
BIOS : 5.2-0 (19176)
Firmware : 5.2-0 (19176)
Driver : 7.5-0 (41013)
Boot Flash : 5.2-0 (19176)
SEEPROM (Load version/ Flash version) : 2/ 8
--------------------------------------------------------
Controller ZMM Information
--------------------------------------------------------
Status : ZMM not installed
----------------------------------------------------------------------
Logical device information
----------------------------------------------------------------------
Logical device number 0
Logical device name : VMSTORAGE01
Block Size of member drives : 512 Bytes
RAID level : 10
Unique Identifier :
Status of logical device : Optimal
Additional details : Quick initialized
Size : 3809270 MB
Parity space : 3809280 MB
Stripe-unit size : 256 KB
Read-cache setting : Enabled
Read-cache status : On
Write-cache setting : Disabled
Write-cache status : Off
Partitioned : Yes
Protected by Hot-Spare : No
Bootable : Yes
Failed stripes : No
Power settings : Disabled
--------------------------------------------------------
Logical device segment information
--------------------------------------------------------
Group 0, Segment 0 : Present (Controller:1,Connector:1,Device:0) WD-
Group 0, Segment 1 : Present (Controller:1,Connector:1,Device:1) WD-
Group 1, Segment 0 : Present (Controller:1,Connector:1,Device:2) WD-
Group 1, Segment 1 : Present (Controller:1,Connector:1,Device:3) WD-
----------------------------------------------------------------------
Physical Device information
----------------------------------------------------------------------
Device #0
Device is a Hard drive
State : Online
Block Size : 512 Bytes
Supported : Yes
Transfer Speed : SATA 6.0 Gb/s
Reported Channel,Device(T:L) : 0,4(4:0)
Reported Location : Connector 1, Device 0
Vendor : WDC
Model : WD20EFRX-68EUZN0
Firmware : 80.00A80
Serial number :
World-wide name :
Reserved Size : 3163160 KB
Used Size : 1904640 MB
Unused Size : 64 KB
Total Size : 1907729 MB
Write Cache : Disabled (write-through)
FRU : None
S.M.A.R.T. : No
S.M.A.R.T. warnings : 0
Power State : Full rpm
Supported Power States : Full rpm,Powered off
SSD : No
Temperature : Not Supported
NCQ status : Enabled
Device #1
Device is a Hard drive
State : Online
Block Size : 512 Bytes
Supported : Yes
Transfer Speed : SATA 6.0 Gb/s
Reported Channel,Device(T:L) : 0,5(5:0)
Reported Location : Connector 1, Device 1
Vendor : WDC
Model : WD20EFRX-68EUZN0
Firmware : 80.00A80
Serial number :
World-wide name :
Reserved Size : 3163160 KB
Used Size : 1904640 MB
Unused Size : 64 KB
Total Size : 1907729 MB
Write Cache : Disabled (write-through)
FRU : None
S.M.A.R.T. : No
S.M.A.R.T. warnings : 0
Power State : Full rpm
Supported Power States : Full rpm,Powered off
SSD : No
Temperature : Not Supported
NCQ status : Enabled
Device #2
Device is a Hard drive
State : Online
Block Size : 512 Bytes
Supported : Yes
Transfer Speed : SATA 3.0 Gb/s
Reported Channel,Device(T:L) : 0,6(6:0)
Reported Location : Connector 1, Device 2
Vendor : WDC
Model : WD20EFRX-68EUZN0
Firmware : 80.00A80
Serial number :
World-wide name :
Reserved Size : 3163160 KB
Used Size : 1904640 MB
Unused Size : 64 KB
Total Size : 1907729 MB
Write Cache : Disabled (write-through)
FRU : None
S.M.A.R.T. : No
S.M.A.R.T. warnings : 0
Power State : Full rpm
Supported Power States : Full rpm,Powered off
SSD : No
Temperature : Not Supported
NCQ status : Enabled
Device #3
Device is a Hard drive
State : Online
Block Size : 512 Bytes
Supported : Yes
Transfer Speed : SATA 6.0 Gb/s
Reported Channel,Device(T:L) : 0,7(7:0)
Reported Location : Connector 1, Device 3
Vendor : WDC
Model : WD20EFRX-68EUZN0
Firmware : 80.00A80
Serial number :
World-wide name :
Reserved Size : 3163160 KB
Used Size : 1904640 MB
Unused Size : 64 KB
Total Size : 1907729 MB
Write Cache : Disabled (write-through)
FRU : None
S.M.A.R.T. : No
S.M.A.R.T. warnings : 0
Power State : Full rpm
Supported Power States : Full rpm,Powered off
SSD : No
Temperature : Not Supported
NCQ status : Enabled