Entre na BIOS do Controlador, selecione a matriz degradada e pressione CTRL + R para reconstruir a matriz.
Eu tenho um problema com um RAID 10, tenho 4 discos em raid. Um disco acaba de ser trocado (0,3). Mas eu não posso reconstruir o array. O dispositivo lógico é definido como "Ausente".
Todos os comandos retornam para mim o seguinte erro
/usr/StorMan# /usr/StorMan/arcconf setstate 1 device 0 3 rdyControllers found: 1 The device specified does not exist. Command aborted.
/usr/StorMan# /usr/StorMan/arcconf getconfig 1
Controllers found: 1
----------------------------------------------------------------------
Controller information
----------------------------------------------------------------------
Controller Status : Optimal
Channel description : SAS/SATA
Controller Model : Adaptec 2405
Controller Serial Number : 2D2711FE327
Physical Slot : 16
Temperature : 68 C/ 154 F (Normal)
Installed memory : 128 MB
Copyback : Disabled
Background consistency check : Disabled
Automatic Failover : Enabled
Global task priority : High
Performance Mode : Default/Dynamic
Stayawake period : Disabled
Spinup limit internal drives : 0
Spinup limit external drives : 0
Defunct disk drive count : 0
Logical devices/Failed/Degraded : 1/0/1
SSDs assigned to MaxIQ Cache pool : 0
Maximum SSDs allowed in MaxIQ Cache pool : 8
MaxIQ Read Cache Pool Size : 0.000 GB
MaxIQ cache fetch rate : 0
MaxIQ Cache Read, Write Balance Factor : 3,1
NCQ status : Enabled
Statistics data collection mode : Enabled
--------------------------------------------------------
Controller Version Information
--------------------------------------------------------
BIOS : 5.2-0 (18937)
Firmware : 5.2-0 (18937)
Driver : 1.1-7 (28000)
Boot Flash : 5.2-0 (18937)
----------------------------------------------------------------------
Logical device information
----------------------------------------------------------------------
Logical device number 0
Logical device name :
RAID level : 10
Status of logical device : Degraded
Size : 3809270 MB
Stripe-unit size : 256 KB
Read-cache mode : Enabled
MaxIQ preferred cache setting : Enabled
MaxIQ cache setting : Disabled
Write-cache mode : Enabled (write-back)
Write-cache setting : Enabled (write-back)
Partitioned : Yes
Protected by Hot-Spare : No
Bootable : Yes
Failed stripes : Yes
Power settings : Disabled
--------------------------------------------------------
Logical device segment information
--------------------------------------------------------
Group 0, Segment 0 : Present (0,1) W1F20KQ9
Group 0, Segment 1 : Present (0,0) Z34063KS
Group 1, Segment 0 : Present (0,2) W1E2PW1C
Group 1, Segment 1 : Missing
----------------------------------------------------------------------
Physical Device information
----------------------------------------------------------------------
Device #0
Device is a Hard drive
State : Online
Supported : Yes
Transfer Speed : SATA 3.0 Gb/s
Reported Channel,Device(T:L) : 0,0(0:0)
Reported Location : Connector 0, Device 0
Vendor :
Model : ST2000DM001-1CH1
Firmware : CC24
Serial number : Z34063KS
Size : 1907729 MB
Write Cache : Enabled (write-back)
FRU : None
S.M.A.R.T. : No
S.M.A.R.T. warnings : 0
Power State : Full rpm
Supported Power States : Full rpm,Powered off,Reduced rpm
SSD : No
MaxIQ Cache Capable : No
MaxIQ Cache Assigned : No
NCQ status : Enabled
Device #1
Device is a Hard drive
State : Online
Supported : Yes
Transfer Speed : SATA 3.0 Gb/s
Reported Channel,Device(T:L) : 0,1(1:0)
Reported Location : Connector 0, Device 1
Vendor :
Model : ST2000DM001-1CH1
Firmware : CC24
Serial number : W1F20KQ9
Size : 1907729 MB
Write Cache : Enabled (write-back)
FRU : None
S.M.A.R.T. : No
S.M.A.R.T. warnings : 0
Power State : Full rpm
Supported Power States : Full rpm,Powered off,Reduced rpm
SSD : No
MaxIQ Cache Capable : No
MaxIQ Cache Assigned : No
NCQ status : Enabled
Device #2
Device is a Hard drive
State : Online
Supported : Yes
Transfer Speed : SATA 3.0 Gb/s
Reported Channel,Device(T:L) : 0,2(2:0)
Reported Location : Connector 0, Device 2
Vendor :
Model : ST2000DM001-1CH1
Firmware : CC24
Serial number : W1E2PW1C
Size : 1907729 MB
Write Cache : Enabled (write-back)
FRU : None
S.M.A.R.T. : No
S.M.A.R.T. warnings : 0
Power State : Full rpm
Supported Power States : Full rpm,Powered off,Reduced rpm
SSD : No
MaxIQ Cache Capable : No
MaxIQ Cache Assigned : No
NCQ status : Enabled
Como posso iniciar a reconstrução da matriz?
Entre na BIOS do Controlador, selecione a matriz degradada e pressione CTRL + R para reconstruir a matriz.
Eu tive o mesmo problema e tive que colocar o novo disco no estado HSP (Hot Spare) primeiro. Depois disso, com o failover configurado como on, o processo de reconstrução foi iniciado automaticamente.
/usr/StorMan/arcconf setstate 1 DEVICE 0 26 HSP
Certifique-se de que você tem os IDs, IDs de canal, etc.
correspondentes./usr/StorMan/arcconf getconfig 1 ld 1 | grep Rebuild
Segment 6 : Rebuilding (Controller:1,Enclosure:0,Slot:18) Z1P5PETG