Estou tentando configurar um equipamento do Ubuntu com um adaptador sem fio USB. Eu estou recebendo alguns tempos de latência muito alta, e isso mostra quando SSH'ing na plataforma. Não tenho certeza para onde ir, pois não vejo nenhum erro, e estou bem dentro do alcance do AP. Tentar o adaptador em outra máquina também funciona bem.
Este é um sistema sem cabeçalho, usando o wpa_supplicant da linha de comando para manipular a conexão. O que eu poderia estar fazendo errado?
uname -a
Linux [hostname] 4.4.0-127-generic #153-Ubuntu SMP Sat May 19 10:58:46 UTC 2018 x86_64 x86_64 x86_64 GNU/Linux
iwconfig
wlx[mac address] IEEE 802.11bgn ESSID:"HomeESSID"
Mode:Managed Frequency:2.442 GHz Access Point: [ap mac address]
Bit Rate=90 Mb/s Tx-Power=30 dBm
Retry short limit:7 RTS thr:off Fragment thr:off
Power Management:off
Link Quality=68/70 Signal level=-42 dBm
Rx invalid nwid:0 Rx invalid crypt:0 Rx invalid frag:0
Tx excessive retries:0 Invalid misc:35 Missed beacon:0
ping 192.168.20.1
PING 192.168.20.1 (192.168.20.1) 56(84) bytes of data.
64 bytes from 192.168.20.1: icmp_seq=1 ttl=64 time=11530 ms
64 bytes from 192.168.20.1: icmp_seq=2 ttl=64 time=10521 ms
64 bytes from 192.168.20.1: icmp_seq=10 ttl=64 time=2458 ms
64 bytes from 192.168.20.1: icmp_seq=11 ttl=64 time=31987 ms
64 bytes from 192.168.20.1: icmp_seq=12 ttl=64 time=30980 ms
64 bytes from 192.168.20.1: icmp_seq=13 ttl=64 time=29981 ms
64 bytes from 192.168.20.1: icmp_seq=14 ttl=64 time=28974 ms
64 bytes from 192.168.20.1: icmp_seq=15 ttl=64 time=27966 ms
64 bytes from 192.168.20.1: icmp_seq=16 ttl=64 time=26958 ms
64 bytes from 192.168.20.1: icmp_seq=17 ttl=64 time=25950 ms
64 bytes from 192.168.20.1: icmp_seq=18 ttl=64 time=24942 ms
64 bytes from 192.168.20.1: icmp_seq=19 ttl=64 time=23934 ms
64 bytes from 192.168.20.1: icmp_seq=20 ttl=64 time=22926 ms
64 bytes from 192.168.20.1: icmp_seq=21 ttl=64 time=21918 ms
64 bytes from 192.168.20.1: icmp_seq=22 ttl=64 time=20910 ms
64 bytes from 192.168.20.1: icmp_seq=23 ttl=64 time=19902 ms
64 bytes from 192.168.20.1: icmp_seq=24 ttl=64 time=22339 ms
64 bytes from 192.168.20.1: icmp_seq=25 ttl=64 time=21332 ms
64 bytes from 192.168.20.1: icmp_seq=26 ttl=64 time=20324 ms
64 bytes from 192.168.20.1: icmp_seq=27 ttl=64 time=19316 ms
64 bytes from 192.168.20.1: icmp_seq=28 ttl=64 time=18308 ms
^C
--- 192.168.20.1 ping statistics ---
59 packets transmitted, 28 received, 52% packet loss, time 58440ms
rtt min/avg/max/mdev = 2458.831/18175.113/31987.997/9136.676 ms, pipe 32
lsusb / dmesg
Bus 008 Device 003: ID 148f:7601 Ralink Technology, Corp. MT7601U Wireless Adapter
[ 2.158764] hub 8-1:1.0: USB hub found
[ 2.159136] hub 8-1:1.0: 4 ports detected
[ 2.439281] usb 8-1.1: new high-speed USB device number 3 using xhci_hcd
[ 2.661345] usb 8-1.1: New USB device found, idVendor=148f, idProduct=7601
[ 2.661351] usb 8-1.1: New USB device strings: Mfr=1, Product=2, SerialNumber=3
[ 2.661356] usb 8-1.1: Product: 802.11 n WLAN
[ 2.661360] usb 8-1.1: SerialNumber: 1.0
[ 6.551566] usb 8-1.1: reset high-speed USB device number 3 using xhci_hcd
[ 6.646417] mt7601u 8-1.1:1.0: ASIC revision: 76010001 MAC revision: 76010500
[ 6.649731] mt7601u 8-1.1:1.0: Firmware Version: 0.1.00 Build: 7640 Build time: 201302052146____
[ 7.031385] mt7601u 8-1.1:1.0: EEPROM ver:0c fae:00
[ 7.031943] mt7601u 8-1.1:1.0: EEPROM country region 01 (channels 1-13)
[ 7.262458] mt7601u 8-1.1:1.0 wlx[mac address]: renamed from wlan0