Disco rígido externo detectado, mas não reconhecido. Não é possível montar, não pode formatar, não pode fazer partição

Question

Eu sou novo no Ubuntu e nesta comunidade. Eu tenho uma expansão seagate externa HD (1 TB) que precisa de resgate. Em primeiro lugar, caiu em algum momento. Até então eu poderia usar algum software de recuperação de dados para recuperar meus dados. Mas eu estava impaciente por um processo de recuperação de dados de 10 dias e, assim, desconectei a unidade. Depois disso, as janelas param de reconhecer a unidade. Muito recentemente eu estava pesquisando on-line para encontrar a unidade pode ser reconhecida pelo Ubuntu e felizmente fez. Mas o problema é que nem eu posso criar uma imagem de disco, nem formatá-la, nem fazer partições. não monta. Eu fiz uma extensa pesquisa para descobrir a causa exata do erro. Executei o comando dmseg e coletei algumas informações. As informações relevantes são as seguintes:

[   33.024928] usb 2-1: new SuperSpeed USB device number 2 using xhci_hcd
[   33.043698] usb 2-1: New USB device found, idVendor=0bc2, idProduct=2321
[   33.043701] usb 2-1: New USB device strings: Mfr=1, Product=2, SerialNumber=3
[   33.043702] usb 2-1: Product: Expansion
[   33.043703] usb 2-1: Manufacturer: Seagate 
[   33.043705] usb 2-1: SerialNumber: NA4AT906
[   33.055276] usb-storage 2-1:1.0: USB Mass Storage device detected
[   33.055796] scsi host4: usb-storage 2-1:1.0
[   33.055897] usbcore: registered new interface driver usb-storage
[   33.057513] usbcore: registered new interface driver uas
[   34.053914] scsi 4:0:0:0: Direct-Access     Seagate  Expansion        0219 PQ: 0 ANSI: 6
[   34.054233] sd 4:0:0:0: Attached scsi generic sg1 type 0
[   55.120163] sd 4:0:0:0: [sdb] Spinning up disk...
[   59.640823] usb 2-1: Disable of device-initiated U1 failed.
[   59.644262] usb 2-1: Disable of device-initiated U2 failed.
[   60.367518] usb 2-1: USB disconnect, device number 2
[   61.380448] .ready
[   61.380624] sd 4:0:0:0: [sdb] Read Capacity(10) failed: Result: hostbyte=DID_NO_CONNECT driverbyte=DRIVER_OK
[   61.380628] sd 4:0:0:0: [sdb] Sense not available.
[   61.380662] sd 4:0:0:0: [sdb] Write Protect is off
[   61.380673] sd 4:0:0:0: [sdb] Mode Sense: 00 00 00 00
[   61.380709] sd 4:0:0:0: [sdb] Asking for cache data failed
[   61.380722] sd 4:0:0:0: [sdb] Assuming drive cache: write through
[   61.381302] sd 4:0:0:0: [sdb] Read Capacity(10) failed: Result: hostbyte=DID_NO_CONNECT driverbyte=DRIVER_OK
[   61.381304] sd 4:0:0:0: [sdb] Sense not available.
[   61.381317] sd 4:0:0:0: [sdb] Attached SCSI disk
[  116.391733] systemd[1]: apt-daily.timer: Adding 17min 55.120014s random time.
[  180.155884] usb 2-1: new SuperSpeed USB device number 3 using xhci_hcd
[  180.172597] usb 2-1: New USB device found, idVendor=0bc2, idProduct=2321
[  180.172601] usb 2-1: New USB device strings: Mfr=2, Product=3, SerialNumber=1
[  180.172603] usb 2-1: Product: Expansion
[  180.172605] usb 2-1: Manufacturer: Seagate
[  180.172607] usb 2-1: SerialNumber: 2HC015KJ
[  180.174591] scsi host5: uas
[  180.176468] scsi 5:0:0:0: Direct-Access     Seagate  Expansion        0502 PQ: 0 ANSI: 6
[  180.176973] sd 5:0:0:0: Attached scsi generic sg1 type 0
[  180.177288] sd 5:0:0:0: [sdb] Spinning up disk...
[  181.178895] ................................................................................
[  261.140098] usb 2-1: USB disconnect, device number 3
[  261.426865] .ready
[  261.586851] sd 5:0:0:0: [sdb] Read Capacity(16) failed: Result: hostbyte=DID_ERROR driverbyte=DRIVER_OK
[  261.586854] sd 5:0:0:0: [sdb] Sense not available.
[  261.706802] sd 5:0:0:0: [sdb] Read Capacity(10) failed: Result: hostbyte=DID_ERROR driverbyte=DRIVER_OK
[  261.706806] sd 5:0:0:0: [sdb] Sense not available.
[  261.794720] sd 5:0:0:0: [sdb] Write Protect is off
[  261.794723] sd 5:0:0:0: [sdb] Mode Sense: 00 00 00 00
[  261.834688] sd 5:0:0:0: [sdb] Asking for cache data failed
[  261.834692] sd 5:0:0:0: [sdb] Assuming drive cache: write through
[  262.062590] sd 5:0:0:0: [sdb] Read Capacity(16) failed: Result: hostbyte=DID_ERROR driverbyte=DRIVER_OK
[  262.062594] sd 5:0:0:0: [sdb] Sense not available.
[  262.182519] sd 5:0:0:0: [sdb] Read Capacity(10) failed: Result: hostbyte=DID_ERROR driverbyte=DRIVER_OK
[  262.182522] sd 5:0:0:0: [sdb] Sense not available.
[  262.422368] sd 5:0:0:0: [sdb] Attached SCSI disk
[  275.958597] usb 2-2: new SuperSpeed USB device number 4 using xhci_hcd
[  275.975347] usb 2-2: New USB device found, idVendor=0bc2, idProduct=2321
[  275.975351] usb 2-2: New USB device strings: Mfr=2, Product=3, SerialNumber=1
[  275.975353] usb 2-2: Product: Expansion
[  275.975355] usb 2-2: Manufacturer: Seagate
[  275.975356] usb 2-2: SerialNumber: 2HC015KJ
[  275.977125] scsi host6: uas
[  275.977598] scsi 6:0:0:0: Direct-Access     Seagate  Expansion        0502 PQ: 0 ANSI: 6
[  275.978151] sd 6:0:0:0: Attached scsi generic sg1 type 0
[  275.978258] sd 6:0:0:0: [sdb] Spinning up disk...
[  276.977994] ...................................................................................................
[  376.245447] usb 2-2: USB disconnect, device number 4
[  376.245528] sd 6:0:0:0: tag#0 uas_zap_pending 0 uas-tag 1 inflight: CMD 
[  376.245531] sd 6:0:0:0: tag#0 CDB: Test Unit Ready 00 00 00 00 00 00
[  376.245554] ready
[  376.361931] sd 6:0:0:0: [sdb] Read Capacity(16) failed: Result: hostbyte=DID_ERROR driverbyte=DRIVER_OK
[  376.361935] sd 6:0:0:0: [sdb] Sense not available.
[  376.482049] sd 6:0:0:0: [sdb] Read Capacity(10) failed: Result: hostbyte=DID_ERROR driverbyte=DRIVER_OK
[  376.482052] sd 6:0:0:0: [sdb] Sense not available.
[  376.570129] sd 6:0:0:0: [sdb] Write Protect is off
[  376.570132] sd 6:0:0:0: [sdb] Mode Sense: 00 00 00 00
[  376.610165] sd 6:0:0:0: [sdb] Asking for cache data failed
[  376.610169] sd 6:0:0:0: [sdb] Assuming drive cache: write through
[  376.842367] sd 6:0:0:0: [sdb] Read Capacity(16) failed: Result: hostbyte=DID_ERROR driverbyte=DRIVER_OK
[  376.842370] sd 6:0:0:0: [sdb] Sense not available.
[  376.962439] sd 6:0:0:0: [sdb] Read Capacity(10) failed: Result: hostbyte=DID_ERROR driverbyte=DRIVER_OK
[  376.962442] sd 6:0:0:0: [sdb] Sense not available.
[  377.162638] sd 6:0:0:0: [sdb] Attached SCSI disk
[  383.263500] usb 2-2: new SuperSpeed USB device number 5 using xhci_hcd
[  383.280228] usb 2-2: New USB device found, idVendor=0bc2, idProduct=2321
[  383.280232] usb 2-2: New USB device strings: Mfr=2, Product=3, SerialNumber=1
[  383.280234] usb 2-2: Product: Expansion
[  383.280236] usb 2-2: Manufacturer: Seagate
[  383.280238] usb 2-2: SerialNumber: 2HC015KJ
[  383.282026] scsi host7: uas
[  383.283790] scsi 7:0:0:0: Direct-Access     Seagate  Expansion        0502 PQ: 0 ANSI: 6
[  383.284411] sd 7:0:0:0: Attached scsi generic sg1 type 0
[  383.284438] sd 7:0:0:0: [sdb] Spinning up disk...
[  384.288132] ..............................
[  414.341158] usb 2-2: USB disconnect, device number 5
[  414.426199] .ready
[  414.586320] sd 7:0:0:0: [sdb] Read Capacity(16) failed: Result: hostbyte=DID_ERROR driverbyte=DRIVER_OK
[  414.586323] sd 7:0:0:0: [sdb] Sense not available.
[  414.706355] sd 7:0:0:0: [sdb] Read Capacity(10) failed: Result: hostbyte=DID_ERROR driverbyte=DRIVER_OK
[  414.706360] sd 7:0:0:0: [sdb] Sense not available.
[  414.794375] sd 7:0:0:0: [sdb] Write Protect is off
[  414.794379] sd 7:0:0:0: [sdb] Mode Sense: 00 00 00 00
[  414.834391] sd 7:0:0:0: [sdb] Asking for cache data failed
[  414.834395] sd 7:0:0:0: [sdb] Assuming drive cache: write through
[  415.062455] sd 7:0:0:0: [sdb] Read Capacity(16) failed: Result: hostbyte=DID_ERROR driverbyte=DRIVER_OK
[  415.062458] sd 7:0:0:0: [sdb] Sense not available.
[  415.182491] sd 7:0:0:0: [sdb] Read Capacity(10) failed: Result: hostbyte=DID_ERROR driverbyte=DRIVER_OK
[  415.182495] sd 7:0:0:0: [sdb] Sense not available.
[  415.382544] sd 7:0:0:0: [sdb] Attached SCSI disk
[  436.159245] usb 2-2: new SuperSpeed USB device number 6 using xhci_hcd
[  436.175831] usb 2-2: New USB device found, idVendor=0bc2, idProduct=2321
[  436.175834] usb 2-2: New USB device strings: Mfr=2, Product=3, SerialNumber=1
[  436.175836] usb 2-2: Product: Expansion
[  436.175837] usb 2-2: Manufacturer: Seagate
[  436.175838] usb 2-2: SerialNumber: 2HC015KJ
[  436.177490] scsi host8: uas
[  436.178528] scsi 8:0:0:0: Direct-Access     Seagate  Expansion        0502 PQ: 0 ANSI: 6
[  436.179064] sd 8:0:0:0: Attached scsi generic sg1 type 0
[  436.179388] sd 8:0:0:0: [sdb] Spinning up disk...
[  437.183342] ..ready
[  438.187867] sd 8:0:0:0: [sdb] 1953525167 512-byte logical blocks: (1.00 TB/932 GiB)
[  438.187871] sd 8:0:0:0: [sdb] 2048-byte physical blocks
[  438.401354] sd 8:0:0:0: [sdb] Write Protect is off
[  438.401359] sd 8:0:0:0: [sdb] Mode Sense: 4f 00 00 00
[  438.404691] usb 2-2: cmd cmplt err -71
[  438.404695] xhci_hcd 0000:00:14.0: ERROR Transfer event for disabled endpoint or incorrect stream ring
[  438.404698] xhci_hcd 0000:00:14.0: @000000003fb70700 00000000 00000000 04000000 08078001
[  439.135787] usb 2-2: USB disconnect, device number 6
[  439.136027] sd 8:0:0:0: tag#0 uas_zap_pending 0 uas-tag 1 inflight: CMD 
[  439.136036] sd 8:0:0:0: tag#0 CDB: Mode Sense(6) 1a 00 08 00 04 00
[  439.136109] sd 8:0:0:0: [sdb] Asking for cache data failed
[  439.136119] sd 8:0:0:0: [sdb] Assuming drive cache: write through
[  439.363764] sd 8:0:0:0: [sdb] Read Capacity(16) failed: Result: hostbyte=DID_ERROR driverbyte=DRIVER_OK
[  439.363767] sd 8:0:0:0: [sdb] Sense not available.
[  439.483784] sd 8:0:0:0: [sdb] Read Capacity(10) failed: Result: hostbyte=DID_ERROR driverbyte=DRIVER_OK
[  439.483787] sd 8:0:0:0: [sdb] Sense not available.
[  439.723819] sd 8:0:0:0: [sdb] Attached SCSI disk
[  453.361652] usb 2-2: new SuperSpeed USB device number 7 using xhci_hcd
[  453.378371] usb 2-2: New USB device found, idVendor=0bc2, idProduct=2321
[  453.378373] usb 2-2: New USB device strings: Mfr=2, Product=3, SerialNumber=1
[  453.378375] usb 2-2: Product: Expansion
[  453.378376] usb 2-2: Manufacturer: Seagate
[  453.378377] usb 2-2: SerialNumber: NA4AT906
[  453.380046] scsi host9: uas
[  453.380499] scsi 9:0:0:0: Direct-Access     Seagate  Expansion        0502 PQ: 0 ANSI: 6
[  453.381082] sd 9:0:0:0: [sdb] 1953525167 512-byte logical blocks: (1.00 TB/932 GiB)
[  453.381084] sd 9:0:0:0: [sdb] 4096-byte physical blocks
[  453.381695] sd 9:0:0:0: Attached scsi generic sg1 type 0
[  453.842067] sd 9:0:0:0: [sdb] Write Protect is off
[  453.842071] sd 9:0:0:0: [sdb] Mode Sense: 4f 00 00 00
[  453.842272] sd 9:0:0:0: [sdb] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[  453.853509]  sdb: sdb1
[  453.854847] sd 9:0:0:0: [sdb] Attached SCSI disk
[  501.001736] sd 9:0:0:0: [sdb] Synchronizing SCSI cache
[  501.118525] sd 9:0:0:0: [sdb] Synchronize Cache(10) failed: Result: hostbyte=DID_ERROR driverbyte=DRIVER_OK
[  501.153024] usb 2-2: USB disconnect, device number 7
[  501.527014] usb 2-2: new SuperSpeed USB device number 8 using xhci_hcd
[  501.543688] usb 2-2: New USB device found, idVendor=0bc2, idProduct=2321
[  501.543690] usb 2-2: New USB device strings: Mfr=2, Product=3, SerialNumber=1
[  501.543692] usb 2-2: Product: Expansion
[  501.543693] usb 2-2: Manufacturer: Seagate
[  501.543694] usb 2-2: SerialNumber: NA4AT906
[  501.545329] scsi host10: uas
[  501.546356] scsi 10:0:0:0: Direct-Access     Seagate  Expansion        0502 PQ: 0 ANSI: 6
[  501.546876] sd 10:0:0:0: Attached scsi generic sg1 type 0
[  501.547082] sd 10:0:0:0: [sdb] 1953525167 512-byte logical blocks: (1.00 TB/932 GiB)
[  501.547085] sd 10:0:0:0: [sdb] 4096-byte physical blocks
[  501.547394] sd 10:0:0:0: [sdb] Write Protect is off
[  501.547397] sd 10:0:0:0: [sdb] Mode Sense: 4f 00 00 00
[  501.547554] sd 10:0:0:0: [sdb] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[  503.618587]  sdb: sdb1
[  503.619863] sd 10:0:0:0: [sdb] Attached SCSI disk
[  513.448650] sd 10:0:0:0: [sdb] Synchronizing SCSI cache
[  513.571824] sd 10:0:0:0: [sdb] Synchronize Cache(10) failed: Result: hostbyte=DID_ERROR driverbyte=DRIVER_OK
[  513.604864] usb 2-2: USB disconnect, device number 8
[  513.980307] usb 2-2: new SuperSpeed USB device number 9 using xhci_hcd
[  513.996960] usb 2-2: New USB device found, idVendor=0bc2, idProduct=2321
[  513.996962] usb 2-2: New USB device strings: Mfr=2, Product=3, SerialNumber=1
[  513.996964] usb 2-2: Product: Expansion
[  513.996965] usb 2-2: Manufacturer: Seagate
[  513.996966] usb 2-2: SerialNumber: NA4AT906
[  513.998656] scsi host11: uas
[  513.999666] scsi 11:0:0:0: Direct-Access     Seagate  Expansion        0502 PQ: 0 ANSI: 6
[  514.000116] sd 11:0:0:0: Attached scsi generic sg1 type 0
[  514.000871] sd 11:0:0:0: [sdb] 1953525167 512-byte logical blocks: (1.00 TB/932 GiB)
[  514.000873] sd 11:0:0:0: [sdb] 4096-byte physical blocks
[  514.001488] sd 11:0:0:0: [sdb] Write Protect is off
[  514.001492] sd 11:0:0:0: [sdb] Mode Sense: 4f 00 00 00
[  514.001638] sd 11:0:0:0: [sdb] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[  516.080393]  sdb: sdb1
[  516.081744] sd 11:0:0:0: [sdb] Attached SCSI disk
[  516.947836] usb 2-2: USB disconnect, device number 9
[  516.948257] sd 11:0:0:0: [sdb] Synchronizing SCSI cache
[  517.071106] sd 11:0:0:0: [sdb] Synchronize Cache(10) failed: Result: hostbyte=DID_ERROR driverbyte=DRIVER_OK[   33.024928] usb 2-1: new SuperSpeed USB device number 2 using xhci_hcd
[   33.043698] usb 2-1: New USB device found, idVendor=0bc2, idProduct=2321
[   33.043701] usb 2-1: New USB device strings: Mfr=1, Product=2, SerialNumber=3
[   33.043702] usb 2-1: Product: Expansion
[   33.043703] usb 2-1: Manufacturer: Seagate 
[   33.043705] usb 2-1: SerialNumber: NA4AT906
[   33.055276] usb-storage 2-1:1.0: USB Mass Storage device detected
[   33.055796] scsi host4: usb-storage 2-1:1.0
[   33.055897] usbcore: registered new interface driver usb-storage
[   33.057513] usbcore: registered new interface driver uas
[   34.053914] scsi 4:0:0:0: Direct-Access     Seagate  Expansion        0219 PQ: 0 ANSI: 6
[   34.054233] sd 4:0:0:0: Attached scsi generic sg1 type 0
[   55.120163] sd 4:0:0:0: [sdb] Spinning up disk...
[   59.640823] usb 2-1: Disable of device-initiated U1 failed.
[   59.644262] usb 2-1: Disable of device-initiated U2 failed.
[   60.367518] usb 2-1: USB disconnect, device number 2
[   61.380448] .ready
[   61.380624] sd 4:0:0:0: [sdb] Read Capacity(10) failed: Result: hostbyte=DID_NO_CONNECT driverbyte=DRIVER_OK
[   61.380628] sd 4:0:0:0: [sdb] Sense not available.
[   61.380662] sd 4:0:0:0: [sdb] Write Protect is off
[   61.380673] sd 4:0:0:0: [sdb] Mode Sense: 00 00 00 00
[   61.380709] sd 4:0:0:0: [sdb] Asking for cache data failed
[   61.380722] sd 4:0:0:0: [sdb] Assuming drive cache: write through
[   61.381302] sd 4:0:0:0: [sdb] Read Capacity(10) failed: Result: hostbyte=DID_NO_CONNECT driverbyte=DRIVER_OK
[   61.381304] sd 4:0:0:0: [sdb] Sense not available.
[   61.381317] sd 4:0:0:0: [sdb] Attached SCSI disk
[  116.391733] systemd[1]: apt-daily.timer: Adding 17min 55.120014s random time.
[  180.155884] usb 2-1: new SuperSpeed USB device number 3 using xhci_hcd
[  180.172597] usb 2-1: New USB device found, idVendor=0bc2, idProduct=2321
[  180.172601] usb 2-1: New USB device strings: Mfr=2, Product=3, SerialNumber=1
[  180.172603] usb 2-1: Product: Expansion
[  180.172605] usb 2-1: Manufacturer: Seagate
[  180.172607] usb 2-1: SerialNumber: 2HC015KJ
[  180.174591] scsi host5: uas
[  180.176468] scsi 5:0:0:0: Direct-Access     Seagate  Expansion        0502 PQ: 0 ANSI: 6
[  180.176973] sd 5:0:0:0: Attached scsi generic sg1 type 0
[  180.177288] sd 5:0:0:0: [sdb] Spinning up disk...
[  181.178895] ................................................................................
[  261.140098] usb 2-1: USB disconnect, device number 3
[  261.426865] .ready
[  261.586851] sd 5:0:0:0: [sdb] Read Capacity(16) failed: Result: hostbyte=DID_ERROR driverbyte=DRIVER_OK
[  261.586854] sd 5:0:0:0: [sdb] Sense not available.
[  261.706802] sd 5:0:0:0: [sdb] Read Capacity(10) failed: Result: hostbyte=DID_ERROR driverbyte=DRIVER_OK
[  261.706806] sd 5:0:0:0: [sdb] Sense not available.
[  261.794720] sd 5:0:0:0: [sdb] Write Protect is off
[  261.794723] sd 5:0:0:0: [sdb] Mode Sense: 00 00 00 00
[  261.834688] sd 5:0:0:0: [sdb] Asking for cache data failed
[  261.834692] sd 5:0:0:0: [sdb] Assuming drive cache: write through
[  262.062590] sd 5:0:0:0: [sdb] Read Capacity(16) failed: Result: hostbyte=DID_ERROR driverbyte=DRIVER_OK
[  262.062594] sd 5:0:0:0: [sdb] Sense not available.
[  262.182519] sd 5:0:0:0: [sdb] Read Capacity(10) failed: Result: hostbyte=DID_ERROR driverbyte=DRIVER_OK
[  262.182522] sd 5:0:0:0: [sdb] Sense not available.
[  262.422368] sd 5:0:0:0: [sdb] Attached SCSI disk
[  275.958597] usb 2-2: new SuperSpeed USB device number 4 using xhci_hcd
[  275.975347] usb 2-2: New USB device found, idVendor=0bc2, idProduct=2321
[  275.975351] usb 2-2: New USB device strings: Mfr=2, Product=3, SerialNumber=1
[  275.975353] usb 2-2: Product: Expansion
[  275.975355] usb 2-2: Manufacturer: Seagate
[  275.975356] usb 2-2: SerialNumber: 2HC015KJ
[  275.977125] scsi host6: uas
[  275.977598] scsi 6:0:0:0: Direct-Access     Seagate  Expansion        0502 PQ: 0 ANSI: 6
[  275.978151] sd 6:0:0:0: Attached scsi generic sg1 type 0
[  275.978258] sd 6:0:0:0: [sdb] Spinning up disk...
[  276.977994] ...................................................................................................
[  376.245447] usb 2-2: USB disconnect, device number 4
[  376.245528] sd 6:0:0:0: tag#0 uas_zap_pending 0 uas-tag 1 inflight: CMD 
[  376.245531] sd 6:0:0:0: tag#0 CDB: Test Unit Ready 00 00 00 00 00 00
[  376.245554] ready
[  376.361931] sd 6:0:0:0: [sdb] Read Capacity(16) failed: Result: hostbyte=DID_ERROR driverbyte=DRIVER_OK
[  376.361935] sd 6:0:0:0: [sdb] Sense not available.
[  376.482049] sd 6:0:0:0: [sdb] Read Capacity(10) failed: Result: hostbyte=DID_ERROR driverbyte=DRIVER_OK
[  376.482052] sd 6:0:0:0: [sdb] Sense not available.
[  376.570129] sd 6:0:0:0: [sdb] Write Protect is off
[  376.570132] sd 6:0:0:0: [sdb] Mode Sense: 00 00 00 00
[  376.610165] sd 6:0:0:0: [sdb] Asking for cache data failed
[  376.610169] sd 6:0:0:0: [sdb] Assuming drive cache: write through
[  376.842367] sd 6:0:0:0: [sdb] Read Capacity(16) failed: Result: hostbyte=DID_ERROR driverbyte=DRIVER_OK
[  376.842370] sd 6:0:0:0: [sdb] Sense not available.
[  376.962439] sd 6:0:0:0: [sdb] Read Capacity(10) failed: Result: hostbyte=DID_ERROR driverbyte=DRIVER_OK
[  376.962442] sd 6:0:0:0: [sdb] Sense not available.
[  377.162638] sd 6:0:0:0: [sdb] Attached SCSI disk
[  383.263500] usb 2-2: new SuperSpeed USB device number 5 using xhci_hcd
[  383.280228] usb 2-2: New USB device found, idVendor=0bc2, idProduct=2321
[  383.280232] usb 2-2: New USB device strings: Mfr=2, Product=3, SerialNumber=1
[  383.280234] usb 2-2: Product: Expansion
[  383.280236] usb 2-2: Manufacturer: Seagate
[  383.280238] usb 2-2: SerialNumber: 2HC015KJ
[  383.282026] scsi host7: uas
[  383.283790] scsi 7:0:0:0: Direct-Access     Seagate  Expansion        0502 PQ: 0 ANSI: 6
[  383.284411] sd 7:0:0:0: Attached scsi generic sg1 type 0
[  383.284438] sd 7:0:0:0: [sdb] Spinning up disk...
[  384.288132] ..............................
[  414.341158] usb 2-2: USB disconnect, device number 5
[  414.426199] .ready
[  414.586320] sd 7:0:0:0: [sdb] Read Capacity(16) failed: Result: hostbyte=DID_ERROR driverbyte=DRIVER_OK
[  414.586323] sd 7:0:0:0: [sdb] Sense not available.
[  414.706355] sd 7:0:0:0: [sdb] Read Capacity(10) failed: Result: hostbyte=DID_ERROR driverbyte=DRIVER_OK
[  414.706360] sd 7:0:0:0: [sdb] Sense not available.
[  414.794375] sd 7:0:0:0: [sdb] Write Protect is off
[  414.794379] sd 7:0:0:0: [sdb] Mode Sense: 00 00 00 00
[  414.834391] sd 7:0:0:0: [sdb] Asking for cache data failed
[  414.834395] sd 7:0:0:0: [sdb] Assuming drive cache: write through
[  415.062455] sd 7:0:0:0: [sdb] Read Capacity(16) failed: Result: hostbyte=DID_ERROR driverbyte=DRIVER_OK
[  415.062458] sd 7:0:0:0: [sdb] Sense not available.
[  415.182491] sd 7:0:0:0: [sdb] Read Capacity(10) failed: Result: hostbyte=DID_ERROR driverbyte=DRIVER_OK
[  415.182495] sd 7:0:0:0: [sdb] Sense not available.
[  415.382544] sd 7:0:0:0: [sdb] Attached SCSI disk
[  436.159245] usb 2-2: new SuperSpeed USB device number 6 using xhci_hcd
[  436.175831] usb 2-2: New USB device found, idVendor=0bc2, idProduct=2321
[  436.175834] usb 2-2: New USB device strings: Mfr=2, Product=3, SerialNumber=1
[  436.175836] usb 2-2: Product: Expansion
[  436.175837] usb 2-2: Manufacturer: Seagate
[  436.175838] usb 2-2: SerialNumber: 2HC015KJ
[  436.177490] scsi host8: uas
[  436.178528] scsi 8:0:0:0: Direct-Access     Seagate  Expansion        0502 PQ: 0 ANSI: 6
[  436.179064] sd 8:0:0:0: Attached scsi generic sg1 type 0
[  436.179388] sd 8:0:0:0: [sdb] Spinning up disk...
[  437.183342] ..ready
[  438.187867] sd 8:0:0:0: [sdb] 1953525167 512-byte logical blocks: (1.00 TB/932 GiB)
[  438.187871] sd 8:0:0:0: [sdb] 2048-byte physical blocks
[  438.401354] sd 8:0:0:0: [sdb] Write Protect is off
[  438.401359] sd 8:0:0:0: [sdb] Mode Sense: 4f 00 00 00
[  438.404691] usb 2-2: cmd cmplt err -71
[  438.404695] xhci_hcd 0000:00:14.0: ERROR Transfer event for disabled endpoint or incorrect stream ring
[  438.404698] xhci_hcd 0000:00:14.0: @000000003fb70700 00000000 00000000 04000000 08078001
[  439.135787] usb 2-2: USB disconnect, device number 6
[  439.136027] sd 8:0:0:0: tag#0 uas_zap_pending 0 uas-tag 1 inflight: CMD 
[  439.136036] sd 8:0:0:0: tag#0 CDB: Mode Sense(6) 1a 00 08 00 04 00
[  439.136109] sd 8:0:0:0: [sdb] Asking for cache data failed
[  439.136119] sd 8:0:0:0: [sdb] Assuming drive cache: write through
[  439.363764] sd 8:0:0:0: [sdb] Read Capacity(16) failed: Result: hostbyte=DID_ERROR driverbyte=DRIVER_OK
[  439.363767] sd 8:0:0:0: [sdb] Sense not available.
[  439.483784] sd 8:0:0:0: [sdb] Read Capacity(10) failed: Result: hostbyte=DID_ERROR driverbyte=DRIVER_OK
[  439.483787] sd 8:0:0:0: [sdb] Sense not available.
[  439.723819] sd 8:0:0:0: [sdb] Attached SCSI disk
[  453.361652] usb 2-2: new SuperSpeed USB device number 7 using xhci_hcd
[  453.378371] usb 2-2: New USB device found, idVendor=0bc2, idProduct=2321
[  453.378373] usb 2-2: New USB device strings: Mfr=2, Product=3, SerialNumber=1
[  453.378375] usb 2-2: Product: Expansion
[  453.378376] usb 2-2: Manufacturer: Seagate
[  453.378377] usb 2-2: SerialNumber: NA4AT906
[  453.380046] scsi host9: uas
[  453.380499] scsi 9:0:0:0: Direct-Access     Seagate  Expansion        0502 PQ: 0 ANSI: 6
[  453.381082] sd 9:0:0:0: [sdb] 1953525167 512-byte logical blocks: (1.00 TB/932 GiB)
[  453.381084] sd 9:0:0:0: [sdb] 4096-byte physical blocks
[  453.381695] sd 9:0:0:0: Attached scsi generic sg1 type 0
[  453.842067] sd 9:0:0:0: [sdb] Write Protect is off
[  453.842071] sd 9:0:0:0: [sdb] Mode Sense: 4f 00 00 00
[  453.842272] sd 9:0:0:0: [sdb] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[  453.853509]  sdb: sdb1
[  453.854847] sd 9:0:0:0: [sdb] Attached SCSI disk
[  501.001736] sd 9:0:0:0: [sdb] Synchronizing SCSI cache
[  501.118525] sd 9:0:0:0: [sdb] Synchronize Cache(10) failed: Result: hostbyte=DID_ERROR driverbyte=DRIVER_OK
[  501.153024] usb 2-2: USB disconnect, device number 7
[  501.527014] usb 2-2: new SuperSpeed USB device number 8 using xhci_hcd
[  501.543688] usb 2-2: New USB device found, idVendor=0bc2, idProduct=2321
[  501.543690] usb 2-2: New USB device strings: Mfr=2, Product=3, SerialNumber=1
[  501.543692] usb 2-2: Product: Expansion
[  501.543693] usb 2-2: Manufacturer: Seagate
[  501.543694] usb 2-2: SerialNumber: NA4AT906
[  501.545329] scsi host10: uas
[  501.546356] scsi 10:0:0:0: Direct-Access     Seagate  Expansion        0502 PQ: 0 ANSI: 6
[  501.546876] sd 10:0:0:0: Attached scsi generic sg1 type 0
[  501.547082] sd 10:0:0:0: [sdb] 1953525167 512-byte logical blocks: (1.00 TB/932 GiB)
[  501.547085] sd 10:0:0:0: [sdb] 4096-byte physical blocks
[  501.547394] sd 10:0:0:0: [sdb] Write Protect is off
[  501.547397] sd 10:0:0:0: [sdb] Mode Sense: 4f 00 00 00
[  501.547554] sd 10:0:0:0: [sdb] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[  503.618587]  sdb: sdb1
[  503.619863] sd 10:0:0:0: [sdb] Attached SCSI disk
[  513.448650] sd 10:0:0:0: [sdb] Synchronizing SCSI cache
[  513.571824] sd 10:0:0:0: [sdb] Synchronize Cache(10) failed: Result: hostbyte=DID_ERROR driverbyte=DRIVER_OK
[  513.604864] usb 2-2: USB disconnect, device number 8
[  513.980307] usb 2-2: new SuperSpeed USB device number 9 using xhci_hcd
[  513.996960] usb 2-2: New USB device found, idVendor=0bc2, idProduct=2321
[  513.996962] usb 2-2: New USB device strings: Mfr=2, Product=3, SerialNumber=1
[  513.996964] usb 2-2: Product: Expansion
[  513.996965] usb 2-2: Manufacturer: Seagate
[  513.996966] usb 2-2: SerialNumber: NA4AT906
[  513.998656] scsi host11: uas
[  513.999666] scsi 11:0:0:0: Direct-Access     Seagate  Expansion        0502 PQ: 0 ANSI: 6
[  514.000116] sd 11:0:0:0: Attached scsi generic sg1 type 0
[  514.000871] sd 11:0:0:0: [sdb] 1953525167 512-byte logical blocks: (1.00 TB/932 GiB)
[  514.000873] sd 11:0:0:0: [sdb] 4096-byte physical blocks
[  514.001488] sd 11:0:0:0: [sdb] Write Protect is off
[  514.001492] sd 11:0:0:0: [sdb] Mode Sense: 4f 00 00 00
[  514.001638] sd 11:0:0:0: [sdb] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[  516.080393]  sdb: sdb1
[  516.081744] sd 11:0:0:0: [sdb] Attached SCSI disk
[  516.947836] usb 2-2: USB disconnect, device number 9
[  516.948257] sd 11:0:0:0: [sdb] Synchronizing SCSI cache
[  517.071106] sd 11:0:0:0: [sdb] Synchronize Cache(10) failed: Result: hostbyte=DID_ERROR driverbyte=DRIVER_OK

Isso é muito demorado e eu realmente aprecio se alguém puder ler as informações acima para me informar sobre o problema com o disco.

Eu tenho informações memoráveis e confidenciais, para tentar recuperar-me de uma empresa profissional e gostaria de fazer isso sozinho.

Qualquer ajuda é realmente apreciada.

Obrigado

    

Answer 1

Já experimentou o comando ntfsfix? Às vezes o disco não sai corretamente no Windows e você precisa consertá-lo antes de ler o disco

    

Answer 2

Se o disco for um disco de 2 "sem fonte de alimentação externa (" Expansion Portable "), uma razão pode ser que não há energia suficiente para girar o disco quando alimentado via USB, consulte a mensagem

[  180.177288] sd 5:0:0:0: [sdb] Spinning up disk...
[  181.178895] ................................................................................
[  261.140098] usb 2-1: USB disconnect, device number 3

Aqui, um HUB USB ativo pode ajudar.

Se ele é alimentado por sua própria fonte de alimentação ("Expansion Desktop"), parece que o disco está corrompido de alguma forma. Como esse também pode ser o controlador SATA para USB, há mais uma chance de recuperar os dados se o disco em si ainda estiver funcionando:

• Abra cuidadosamente o estojo (pode haver parafusos escondidos por amortecedores de borracha)
• Cuidadosamente tire o disco do estojo
• Obtenha um Adaptador SATA para USB diferente com fonte de alimentação própria e tente com isso
• Ou melhor: se o seu PC tiver uma porta SATA não usada, conecte o disco lá (mais a linha de energia) e tente. Nesse caso, a ferramenta GSmartControl pode ajudar, já que o SMART é suportado por discos modernos quando conectado via SATA (na maioria das vezes não funciona via USB).

O SMART é uma maneira de ler informações sobre o estado do disco e erros ocorridos. Informações sobre como usar GSmartControl consulte, por exemplo, link